Great serviceOn 04/19/2024 by H. P. (verified customer)
In our lineup of over 3100 genuine Hot Spring spa parts are all four designs of the Hot Spring brand of cover lifters. Some of these cover lifters or Retractable Cover Systems (RCS) are designed to attach to the spa and also to the Hot Spring cover. In 1996, all Hot Spring spa covers (Watkins) were equipped with hidden steel inserts embedded into the insulated foam cores. These inserts enabled some styles of Hot Spring cover lifters to attach directly into the edge of their spa covers. Mega beefy design!
Showing 1–30 of 43 results
-
Sku: 37876
Uprite Cover Lifter (7in Clearance)
The Uprite® Lifter is a favorite for close clearance needs If your spa needs to be nudged up close to the house, fence or gazebo then this lifter is ideal The Uprite® (sometimes spelled upright) only requires seven inches (7") of rear clearance to ...read more -
Sku: 71794
Gas Spring-Uprite
The Uprite® Cover Lifter employs two gas shocks that assist in opening the spa cover Sometimes these gas shocks can fall victim to the elements (storms, crazy uncles, frat parties etc ) and need replacing Replacement time is approximately thirty seconds ...read more -
There were two different sized ball studs used on Hot Spring cover lifters One is this 1/4" threaded shaft and the other (3rd qtr 2009) is 5/16" threaded shaft (part 75149) Either one size or the other will be on your cover lifter but not both sizes Ball ...read more
-
Sku: 75103
Gas Spring Lock-Uprite
The Gas Spring lock is used to secure the Uprite Lifter in the open position attaching to only one gas shock This part is typically left off when installing the Uprite Cover Lifter unless the spa is located in a windy area -
This ball stud is found on 3rd quarter 2009 and newer UpRite, Cover Cradle and Cover Cradle II lifters The older cover lifters used a 1/4" threaded shaft ball stud which is part# 71107-BYP
-
Sku: 71793
Angle Bracket-Uprite
Angle bracket for Uprite cover lifter -
This part attaches onto the right side of the spa cover
-
Sku: 73451
Hardware Bag #1, Uprite Cover Lifter
Bag #1 for the upright cover lifter Contains the following: 2 x 1/4 x 20 5/8" Hex Bolts 2 x 1/4 x 1" Fender Washers 2 x 2 Hold Deck Hinge 10 x #10 Washers 8 x #10 1/2" Square Panhead Self Tapping Screws 10 x #10 1 1/2" Square Pan Tapping Screws 12 ...read more -
Right side bracket (as you are facing the spa folding the cover away from you) for the Uprite cover lifter
-
Sku: 71789
Upright Side Bracket Assembly, Left Side
Left side bracket (as you are facing the spa folding the cover away from you) of the Uprite cover lifter -
Sku: 75152
Upright Extension Tube
One pair (quantity of two) of extensions for the Uprite cover lifter -
Sku: 71775
Gliderite Base Tube Assembly, Rightside
The Gliderite has three black tubular bars (left, center and right) that fit together and form one long bar that mounts near the bottom base of the spa This tube is for the right-hand side only -
This right-side Corner Tube Assembly comes with the pivot collar and screw
-
Sku: 71751
Gliderite Bearing
This bearing is placed over the ¼” – 20 x 1” Hex Head Bolt -
This slot tube is found on both sides of the Gliderite and connects to the opposite end of the sidearm that is attached to the spa cover Illustration (# 11) on the Gliderite parts diagram
-
Sku: 71742
Bolt, #10 X 2-1/2in
OBSOLETE These bolts are used with washers to fasten the left and right Base Tubes on a Gliderite Illustration (# 5) on the Gliderite parts diagram -
Sku: 75150
Uprite Channel Pivot Assembly, Left Side
This part attaches onto the left side of the spa cover -
Sku: 71744
Washer, Gliderite
These washers are used with the ¼” – 20 x 5/8” Hex Head Bolts & ¼” – 20 x 1” Hex Head Bolt on the Gliderite and also used on the Uprite cover lifter -
Sku: 71217
Hex Head Bolt, 1/4in-#20 X 1in
This bolt is used to fasten the Slide Lock Bar to the Side Arm -
Sku: 71218
Bolt, #20 X 1/4in. X 2in. Hex Head
Attaches the sidearm to the pivot wheel on all spa models (except the Hot Spring Classic) -
Sku: 78164
Upright Lifter and Pro Lifter Spacer
This spacer is used on Upright cover lifters for HSS (Hot Springs Spas) and Pro Lifter Caldera For 2018 and newer Limelight models – spacer kit PN 78164 is required to install an UpRite lifter (PN 37876) to create space needed due to the small corner ...read more -
Obsolete: Factory replacement suggestion item - complete Uprite Lifter 37876
-
Sku: 72472
Gliderite Sidearm Assembly (Curved)
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com The curved side arm is a black 1" x 1" tubular piece that's used on both sides of the Gliderite Cover ...read more -
Sku: 71977
Sure, Lock Sleeve
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Part of the Sure-Lock for the Uprite Cover Lifter Now included with the 75103 -
Sku: 71105
Bracket, Corner (G/K)
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Bracket, Corner (G/K) -
Sku: 72452
Side Hinge, 11/16in Base with Screw
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com This side hinge screws into the vinyl cover and is used on the Gliderite & Cover Cradle cover lifters ...read more -
OBSOLETE-Use the 71107-BYP
-
Sku: 37872
GlideRite Cover Lifter (14″ Clearance)
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com -
Sku: 73416
Uprite, Pivot Tube, Right Side, Uprite
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com
Showing 1–30 of 43 results