Great customer service. Fast shipping and exactly what I needed.On 05/09/2024 by D. A. (verified customer)
Get high-quality Hot Spring Spa Wood Siding Panels, Equipment Compartment Doors, Wooden Slats, Cover Lifters, Cover Locks, Crack Repair Kits, and other related parts for your spa exterior.
Brand: Hot Spring Pre 89, Limelight
Showing 1–30 of 50 results
-
Sku: 37876Uprite Cover Lifter (7in Clearance)
The Uprite® Lifter is a favorite for close clearance needs If your spa needs to be nudged up close to the house, fence or gazebo then this lifter is ideal The Uprite® (sometimes spelled upright) only requires seven inches (7") of rear clearance to ...read more -
The CoverCradle® is our smoothest operator As the spa cover is folded back the “cradle” design is assisted by dual pneumatic gas shocks lowering it to a gentle rest It only needs twenty-four inches (24") of rear clearance -
The CoverCradle® II has all the features of its big brother in a single pneumatic gas shock design Our customers who choose either of the CoverCradle® models don't have clearance issues and favor the lower resting point of the cover for increased ...read more -
The Lift 'N Glide® is easy to install and ready to ship This lifter only requires fourteen inches (14") of rear clearance and three inches (3") on each side -
Sku: 72573Side Arm Assembly, Cover Cradle
This black side arm is used on the CoverCradle and the CoverCradle II It attaches to the side of the spa cover and then to the side of the spa -
Sku: 71515Cover Lock Kit, 4 Sets, Black
Four sets of black cover locks This kit has both the female end (mounts onto the spa) and the male end (attaches to the cover strap) and the mounting screws All four of these sets come standard in this kit This coverlock kit replaces all other colors and ...read more -
Sku: 71794Gas Spring-Uprite
The Uprite® Cover Lifter employs two gas shocks that assist in opening the spa cover Sometimes these gas shocks can fall victim to the elements (storms, crazy uncles, frat parties etc ) and need replacing Replacement time is approximately thirty seconds ...read more -
There were two different sized ball studs used on Hot Spring cover lifters One is this 1/4" threaded shaft and the other (3rd qtr 2009) is 5/16" threaded shaft (part 75149) Either one size or the other will be on your cover lifter but not both sizes Ball ...read more -
Sku: 73335Espresso Slat, Flat
This is a single width slat in synthetic espresso material for use on Hot Springs and Hot Spot models Check your serial number in the Parts Finder above to be sure this part is for your spa -
Sku: 72574Hardware Bag #1, Cover Cradle
This Cover Cradle & Cover Cradle II hardware bag #1 includes the following: Four Hole Side Hinge (Qty 2) Four Hole Rear Hinge (Qty 2) #10 x 1" Flat Head Screws (Qty 8) #10 x 1-1/2" Flat Head Screws (Qty 8) Note: The items in this hardware bag are ...read more -
Sku: 70322Key, Cover Lock (Set of 2)
These keys (set of two) lock & unlock the spa covers (latches) cover locks that are located on the end of the four straps The cover locks are lockable to help prevent or discourage unauthorized entry into the spa -
Slat, Flat, Wenge, Synthetic Redwood Color Hot Spring Models 2006-2015 This slat makes up the majority of the Side and Back Panels, including the Door PLEASE NOTE: Normal length of slat is 32 75”; however, only the 30 38” length is available ...read more -
Sku: 71095Gas Shock, Cover Cradle
Replacement 40lb gas spring shock for all models of the Cover Cradle cover lifter Gas shock color is black -
Sku: 300040Brass Door Screw Insert, 1/4in
This brass insert is used on the door frames of various spa models to provide attach a door using a stainless steel screw which screws into this insert -
Sku: 74034Gas Shock, Cover Cradle II
Replacement 60lb gas spring shock for all Cover Cradle II cover lifters from the makers of Hot Springs spas The gas shock color is black One of these shocks is used on the Cover Cradle II -
Sku: 75103Gas Spring Lock-Uprite
The Gas Spring lock is used to secure the Uprite Lifter in the open position attaching to only one gas shock This part is typically left off when installing the Uprite Cover Lifter unless the spa is located in a windy area -
This ball stud is found on 3rd quarter 2009 and newer UpRite, Cover Cradle and Cover Cradle II lifters The older cover lifters used a 1/4" threaded shaft ball stud which is part# 71107-BYP -
Sku: 30334Screw, #4 X 1/2in Stainless Steel
Stainless steel screw used in various locations on Hot Spring, Tiger River, Solana, Hot Spot and Limelight spas -
This is a synthetic coastal grey slat in the wenge style used on Hot Springs spas -
Sku: 72775-x1-BYPIntake Vent Screen
This aluminum perforated strip mounts at the bottom of the equipment access door to keep rodents from making their home in the warmth of your Hot Spring or Tiger River spas equipment compartment This screen is cut to length Not available for the Hot Spring ...read more -
Sku: 76549Fibercore Replacement Kit
This Fibercor Replacement Kit can be used on all Hot Spring Spa models from 2007 to 2018 and all 2019 Limelight and Hot Spot Spa models This Kit contains approximately 8 pounds of material, which is about 4 cubic feet -
Sku: 72714Hardware Bag #2, Cover Cradle II
This Cover Cradle II hardware bag #2 includes the following: 1/4"-20 x 3/4" Stainless Steel Hex Bolts (Qty 4) #10 x 1-1/2" Stainless Steel Flat Head Screws (Qty 8) #10 x 1-1/2" Stainless Steel Pan Head Screws (Qty 14) Note: The items in this hardware ...read more -
Flat T slat, Wenge, Synthetic Redwood color found on the siding of Hot Spring Models 2006-2015 -
Sku: 74108Slat, Coastal Gray, Hot Spring
This is a synthetic coastal grey slat in the wenge style used on Hot Springs spas -
This pivot assembly is for the left side of the Cover Cradle II cover lifter as you're facing the lifter from the front This arm attaches to the side of the cover with a bracket and screws The other end attaches near the base of the spa -
Sku: 71793Angle Bracket-Uprite
Angle bracket for Uprite cover lifter -
Sku: 73336Flat T Slat, Espresso, Hot Spring
This is a single width T slat in synthetic espresso material for use on Hot Springs spas made from 2004 to 2008 One of these slats is used on each side of the spa -
Sku: 72572Crosslink Assembly, Cover Cradle
The Crosslink Assembly is the large "U" shaped bar that spans from the right side pivot assembly to the left side on the Cover Cradle and the Cover Cradle II cover lifter -
Sku: 71525Silicone, DOW 732 Clear, 3 oz.
100% clear silicone used to waterproof around various water features above the water line of the spa This item is available from most hardware stores for about the same price -
This pivot assembly is for the right side of the Cover Cradle II cover lifter as you're facing the lifter from the front It attaches to one side of the cover via a bracket and screws, and the other end attaches near the bottom of the edge of the spa
Showing 1–30 of 50 results