It was very easy to select the corret parts for my "serial Number". All parts were correct and operated as required.On 06/20/2024 by M. R. (verified customer)
Get important tools and hardware you need to maintain or fix your spa. This includes Screws, Bolts, Washers, Hose Clamps, Nuts, Power Cables, Silicone, Glue, Foam, Wrenches, Pliers, Custom Tools, and more.
Showing 1–30 of 62 results
-
Sku: 30018
Mounting Bolt, Wavemaster
1/4-20 X 1-1/4" long mounting bolt that secures the pump to the floor of the equipment compartment Used on the Wavemaster 4000, Wavemaster 6000 and Wavemaster 7000 3 jet pumps -
Sku: 70035
Bolt, Hex Hd 3/8in-16 X 1-3/4in, Starite
Stainless steel bolt used to secure the 1HP and 2HP Sta-rite Max-E-Glas jet pump motor to the mounting bracket in the Hot Spring equipment compartment -
Sku: 70059
Bolt, #3/8in-16 X 1in Hex, Starite
Stainless steel bolt used to connect the seal plate to the electric motor on both 1HP and 2HP Sta-rite Max-E-Glas jet pumps -
Sku: 30297
Nut, Volute Clamp, Starite
Used to tighten the volute clamp that binds the volute and seal plate together on all 1HP and 2HP Starite Max-E-Glas jet pumps that were used on some Hot Spring spa models prior to 1994 -
Bolt that secures the motor onto the Wavemaster 7000 (v 1) seal plate
-
This bolt is used to secure the base of the 1st version Wavemaster 7000 jet pump to the motor and also secures the base to the floor of the equipment compartment
-
Sku: 77290
Panel Clip, Door/side, NXT
Door and side panel clip NXT model Highlife Collection Grandee NXT (GGN), Envoy NXT (KKN), JetsetterNXT (JJN) To remove Door/Side Panel, loosen the 2 screws on each clip below the panel Slide Door/Side Panel to the "LEFT" Door/Panel will drop ...read more -
Sku: 30396
Nut, #1/4in-20in Stainless Steel
Stainless steel nut used to secure the 220 volt Hot Spring heater elements (31409-BYP) to the heater housing (70192) -
Sku: 36586
Clip, Extruded Air Valve
Used to hold the air intake for the Freshwater II Ozonator in place on the wall in the equipment compartment near the Ozonator Found in Hotspring and Tiger River Spas with Freshwater II Ozonators -
Sku: 73249
Panel Clips, Male and Female, QTY 4
Panel clips, male/female, for the removable panels on Hot Spring models, quantity of 4 -
Stainless steel bolt used on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps to secure the mounting bracket to the floor in the Hot Spring equipment compartment
-
Non-metallic hinge for all pre-1995 wooden Hot Spring equipment compartment doors (access doors)
-
Sku: 20018
Hinge, 7in
This door hinge was used on the Hot Spring spas -
Sku: 71742
Bolt, #10 X 2-1/2in
OBSOLETE These bolts are used with washers to fasten the left and right Base Tubes on a Gliderite Illustration (# 5) on the Gliderite parts diagram -
Sku: 71217
Hex Head Bolt, 1/4in-#20 X 1in
This bolt is used to fasten the Slide Lock Bar to the Side Arm -
Bolt that secures the suction flange onto the front of the Wavemaster 7000 (v 1)
-
Sku: 37752
Wing Nut,10-24 Stainless Steel
This wing nut is used to hold the bulb clamp in place on the heater body in Tiger River spas from 1992 to 1994 The bulb clamp holds the copper thermostat and hi-limit bulbs to the side of the heater where they are used to monitor the temperature of the spa ...read more -
Sku: 33253
Nut, Speed Narrow
Nut, speed narrow -
Hex bolt, 1/4in-20 x 1-1/2in stainless steel
-
Sku: 32748
Lag Bolt 3in
3in lag bolt -
Sku: 32736
Nut, Lock 1/4in (Thin)
1/4in lock nut -
Sku: 300859
Nut, 2.5mm
This nut is used to secure the circuit board to the back of the control panel bezel on Tiger River spas from 1992-1997 It replaces a small spring clamp that used to do the same job The posts that the nut screws on to are actually plastic and are not ...read more -
Sku: 20007
Hinge, 3.5in, Ivory
This is a Door Hinge, 3 5", Ivory color This is used on early Home/Personal & Indoor/Outdoor Hot Spring Spas -
Sku: 71218
Bolt, #20 X 1/4in. X 2in. Hex Head
Attaches the sidearm to the pivot wheel on all spa models (except the Hot Spring Classic) -
Sku: 34029
Nut 10-24 Nylon
Nut 10-24 Nyloc -
Sku: 34174
Bolt, 1/4in-20 X 5/8in 100 Degree
Bolt, 1/4in-20 x 5/8in 100 degree -
Sku: 35243
Skimmer Backing Plate, Hot Spot 2
This is the backing plate for the skimmer on all 1995-1997 Hot Spot2 spa models -
This nut goes onto the volute bolt that secures the seal place to the volute
-
Sku: 71188
Bolt, 3/8in-24 x 2, pack of 5
Bolt, 3/8in-24 x 2, pack of 5 -
Sku: 31158
Clip, Lid Filter Grandee pre 1989
There are four filter clips (31158) and four screws (30341) to hold the filter lid in place Grandee Pre-1989
Showing 1–30 of 62 results