quick ship ,as described and was perfect transaction. ThanksOn 06/13/2024 by B. H. (verified customer)
Hardware: Ball Stud, Bushing Strain Relief, Hardware, Mounting Kit
Showing all 29 results
-
Sku: 73019Pillow Retainer Screw Kit
The plastic retainers in this kit come in two lengths: The short gray retainers are used if your pillows have remained in place over the years The gray extensions are used only if your pillows have fallen off often in the past -
"Blade Mount" pillow retainer (set of two blades) for all Hot Spring spa pillows and all Limelight spa pillows beginning in the second quarter of 2007 Check the diagrams for the correct pillow retainer -
There were two different sized ball studs used on Hot Spring cover lifters One is this 1/4" threaded shaft and the other (3rd qtr 2009) is 5/16" threaded shaft (part 75149) Either one size or the other will be on your cover lifter but not both sizes Ball ...read more -
Sku: 72574Hardware Bag #1, Cover Cradle
This Cover Cradle & Cover Cradle II hardware bag #1 includes the following: Four Hole Side Hinge (Qty 2) Four Hole Rear Hinge (Qty 2) #10 x 1" Flat Head Screws (Qty 8) #10 x 1-1/2" Flat Head Screws (Qty 8) Note: The items in this hardware bag are ...read more -
Sku: 30099Bushing, Strain Relief
This 3/8" strain relief is used to secure the jet pump(s), circulation pump, light and Ozonator power cords to the bottom of the IQ 2020 Control boxes The strain relief prevents the cord from accidentally being disconnected from inside the control box should ...read more -
This ball stud is found on 3rd quarter 2009 and newer UpRite, Cover Cradle and Cover Cradle II lifters The older cover lifters used a 1/4" threaded shaft ball stud which is part# 71107-BYP -
Sku: 36022Strain Relief 10/3
Heater strain relief used to secure the heaters power cord to the bottom of the IQ Control boxes The strain relief prevents the cord from accidentally being disconnected from inside the control box should the cord be pulled down -
Sku: 30100Strain Relief Bushing, 1/2in
This bushing is used for strain relief of cords that are 1/2" in diameter, such as the cord for the heater in a Hotsprings, Tiger River, or LimeLight spa -
Sku: 72714Hardware Bag #2, Cover Cradle II
This Cover Cradle II hardware bag #2 includes the following: 1/4"-20 x 3/4" Stainless Steel Hex Bolts (Qty 4) #10 x 1-1/2" Stainless Steel Flat Head Screws (Qty 8) #10 x 1-1/2" Stainless Steel Pan Head Screws (Qty 14) Note: The items in this hardware ...read more -
Sku: 30105Romex Clamp 3/4in
This clamp is used as strain relief is used to secure the heater's power cord to the bottom of the IQ Control box The strain relief prevents the cord from accidentally being disconnected from inside the control box should the cord be pulled down -
Sku: 73451Hardware Bag #1, Uprite Cover Lifter
Bag #1 for the upright cover lifter Contains the following: 2 x 1/4 x 20 5/8" Hex Bolts 2 x 1/4 x 1" Fender Washers 2 x 2 Hold Deck Hinge 10 x #10 Washers 8 x #10 1/2" Square Panhead Self Tapping Screws 10 x #10 1 1/2" Square Pan Tapping Screws 12 ...read more -
Sku: 72715Hardware Bag #3, Cover Cradle II
This Cover Cradle II hardware bag #3 is only for spas with removable exterior panels and includes the following: #10 x 2" Stainless Steel Flat Head Screws (Qty 8) #10 x 2" Stainless Steel Pan Head Screws (Qty 14) Note: The items in this hardware bag are ...read more -
Sku: 71614Strain Relief
This strain relief is found on most LX jet pump models -
Sku: 71613Strain Relief #3461
Strain relief #3460 -
Sku: 71072Retainer Clip
Used on the 1995-1999 Hot Spring Dream Pillow Neckjet -
Universal Bushing, 0 875 inch, found in Hot Spot Control Box Assembly (37335) This Bushing protects the Electronic T-Stat (75089) from the metal control box housing This part can be found on the 1998 Hot Spot models -
Sku: 30102Bushing, Snap 3/8in Outside Diameter
This bushing is used around openings through the control box used on pre-1997 Hot Springs spas where the copper tubes for the temperature probes and the cable for the spa power on light pass through -
Mounting plate found on the backside of all 1994-1997 Hot Spring Classic spas control panels -
Sku: 75105Hardware Bag #4 for Upright Cover Lifter
Hardware for the upright spa cover lifter -
Obsolete: Factory replacement suggestion item #72714 Hardware Bag #2 used on the Cover Cradle and Cover Cradle II It contains screws for mounting the cover lifter to the spa and cover All screws use Robertson (square drive) head bits -
Sku: 73166Hardware Bag, Lift ‘N Glide
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Twenty stainless steel screws, 1 1/2" long used to attached the Lift 'N Glide cover lifter to the spa -
Obsolete: Factory replacement suggestion item 75149 This kit (item#7 in the diagram) includes the following parts for the Cover Cradle: 1/4" Ball Stud X 4 1/4" Split Lock Washer X 2 1/4" Slot Nuts X 2 1/4" Nut -
Sku: 73163Clarion Hardware Bag
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com This hardware bag contains all of the hardware necessary to mount five Clarion Light Bars It does not ...read more -
Sku: 34717Extrusion, Mount Clip, Model Z
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Extrusion, Mount Clip, Model Z -
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Mounting Bracket Control Box (Tiger River)
-
Sku: 36016
Mount Plate, Control Panel
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Mount Plate, Control Panel -
Sku: 72716
Hardware Bag #4, Cover Cradle II
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com -
Sku: 72576Cover Cradle Hardware Bag #3
Cover Cradle I Hardware Bag #3 -
Sku: 35204
Freshwater Mounting Kit, Classic only
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com This mounting kit enables the Freshwater Ozonator to mount onto the equipment compartment floor of a ...read more
Showing all 29 results