Good company. Honest. ThanksOn 06/03/2024 by D. S. (verified customer)
Hardware: Bolt, Brace, Hardware, Nut
Showing 1–30 of 56 results
-
Sku: 30018Mounting Bolt, Wavemaster
1/4-20 X 1-1/4" long mounting bolt that secures the pump to the floor of the equipment compartment Used on the Wavemaster 4000, Wavemaster 6000 and Wavemaster 7000 3 jet pumps -
Sku: 70035Bolt, Hex Hd 3/8in-16 X 1-3/4in, Starite
Stainless steel bolt used to secure the 1HP and 2HP Sta-rite Max-E-Glas jet pump motor to the mounting bracket in the Hot Spring equipment compartment -
Sku: 70059Bolt, #3/8in-16 X 1in Hex, Starite
Stainless steel bolt used to connect the seal plate to the electric motor on both 1HP and 2HP Sta-rite Max-E-Glas jet pumps -
Sku: 30297Nut, Volute Clamp, Starite
Used to tighten the volute clamp that binds the volute and seal plate together on all 1HP and 2HP Starite Max-E-Glas jet pumps that were used on some Hot Spring spa models prior to 1994 -
Bolt that secures the motor onto the Wavemaster 7000 (v 1) seal plate -
This bolt is used to secure the base of the 1st version Wavemaster 7000 jet pump to the motor and also secures the base to the floor of the equipment compartment -
Sku: 72574Hardware Bag #1, Cover Cradle
This Cover Cradle & Cover Cradle II hardware bag #1 includes the following: Four Hole Side Hinge (Qty 2) Four Hole Rear Hinge (Qty 2) #10 x 1" Flat Head Screws (Qty 8) #10 x 1-1/2" Flat Head Screws (Qty 8) Note: The items in this hardware bag are ...read more -
Sku: 30396Nut, #1/4in-20in Stainless Steel
Stainless steel nut used to secure the 220 volt Hot Spring heater elements (31409-BYP) to the heater housing (70192) -
Sku: 72714Hardware Bag #2, Cover Cradle II
This Cover Cradle II hardware bag #2 includes the following: 1/4"-20 x 3/4" Stainless Steel Hex Bolts (Qty 4) #10 x 1-1/2" Stainless Steel Flat Head Screws (Qty 8) #10 x 1-1/2" Stainless Steel Pan Head Screws (Qty 14) Note: The items in this hardware ...read more -
Stainless steel bolt used on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps to secure the mounting bracket to the floor in the Hot Spring equipment compartment -
Sku: 73451Hardware Bag #1, Uprite Cover Lifter
Bag #1 for the upright cover lifter Contains the following: 2 x 1/4 x 20 5/8" Hex Bolts 2 x 1/4 x 1" Fender Washers 2 x 2 Hold Deck Hinge 10 x #10 Washers 8 x #10 1/2" Square Panhead Self Tapping Screws 10 x #10 1 1/2" Square Pan Tapping Screws 12 ...read more -
Sku: 71742Bolt, #10 X 2-1/2in
OBSOLETE These bolts are used with washers to fasten the left and right Base Tubes on a Gliderite Illustration (# 5) on the Gliderite parts diagram -
Solid Wood Corner Brace with two vent holes - Hot Spring Spa This solid wood corner brace replaces either the front left/right corner brace which has two ventilation holes for the jet pumps The corner brace should be treated or painted, prior to ...read more -
Sku: 72715Hardware Bag #3, Cover Cradle II
This Cover Cradle II hardware bag #3 is only for spas with removable exterior panels and includes the following: #10 x 2" Stainless Steel Flat Head Screws (Qty 8) #10 x 2" Stainless Steel Pan Head Screws (Qty 14) Note: The items in this hardware bag are ...read more -
Sku: 71217Hex Head Bolt, 1/4in-#20 X 1in
This bolt is used to fasten the Slide Lock Bar to the Side Arm -
Bolt that secures the suction flange onto the front of the Wavemaster 7000 (v 1) -
Sku: 37752Wing Nut,10-24 Stainless Steel
This wing nut is used to hold the bulb clamp in place on the heater body in Tiger River spas from 1992 to 1994 The bulb clamp holds the copper thermostat and hi-limit bulbs to the side of the heater where they are used to monitor the temperature of the spa ...read more -
Sku: 33253Nut, Speed Narrow
Nut, speed narrow -
Hex bolt, 1/4in-20 x 1-1/2in stainless steel -
Sku: 32748Lag Bolt 3in
3in lag bolt -
Sku: 32736Nut, Lock 1/4in (Thin)
1/4in lock nut -
Sku: 300859Nut, 2.5mm
This nut is used to secure the circuit board to the back of the control panel bezel on Tiger River spas from 1992-1997 It replaces a small spring clamp that used to do the same job The posts that the nut screws on to are actually plastic and are not ...read more -
Sku: 71218Bolt, #20 X 1/4in. X 2in. Hex Head
Attaches the sidearm to the pivot wheel on all spa models (except the Hot Spring Classic) -
Sku: 34029Nut 10-24 Nylon
Nut 10-24 Nyloc -
Sku: 34174
Bolt, 1/4in-20 X 5/8in 100 Degree
Bolt, 1/4in-20 x 5/8in 100 degree -
This nut goes onto the volute bolt that secures the seal place to the volute -
Sku: 71188
Bolt, 3/8in-24 x 2, pack of 5
Bolt, 3/8in-24 x 2, pack of 5 -
Sku: 75105Hardware Bag #4 for Upright Cover Lifter
Hardware for the upright spa cover lifter -
Obsolete: Factory replacement suggestion item #72714 Hardware Bag #2 used on the Cover Cradle and Cover Cradle II It contains screws for mounting the cover lifter to the spa and cover All screws use Robertson (square drive) head bits -
Sku: 30393Nut, Brass – Cap #1/4in-20
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Nut, Brass - Cap #1/4in-20
Showing 1–30 of 56 results