The team at Backyardplus.com are the best for anything Hot Springs. Super friendly and knowledgeable.On 06/05/2024 by S. O. (verified customer)
Hardware: Bolt, Bushing Strain Relief, Nut, O Ring
Showing 1–30 of 53 results
-
Sku: 30018Mounting Bolt, Wavemaster
1/4-20 X 1-1/4" long mounting bolt that secures the pump to the floor of the equipment compartment Used on the Wavemaster 4000, Wavemaster 6000 and Wavemaster 7000 3 jet pumps -
Sku: 70035Bolt, Hex Hd 3/8in-16 X 1-3/4in, Starite
Stainless steel bolt used to secure the 1HP and 2HP Sta-rite Max-E-Glas jet pump motor to the mounting bracket in the Hot Spring equipment compartment -
Sku: 70059Bolt, #3/8in-16 X 1in Hex, Starite
Stainless steel bolt used to connect the seal plate to the electric motor on both 1HP and 2HP Sta-rite Max-E-Glas jet pumps -
Sku: 30297Nut, Volute Clamp, Starite
Used to tighten the volute clamp that binds the volute and seal plate together on all 1HP and 2HP Starite Max-E-Glas jet pumps that were used on some Hot Spring spa models prior to 1994 -
Bolt that secures the motor onto the Wavemaster 7000 (v 1) seal plate -
This bolt is used to secure the base of the 1st version Wavemaster 7000 jet pump to the motor and also secures the base to the floor of the equipment compartment -
Sku: 30099Bushing, Strain Relief
This 3/8" strain relief is used to secure the jet pump(s), circulation pump, light and Ozonator power cords to the bottom of the IQ 2020 Control boxes The strain relief prevents the cord from accidentally being disconnected from inside the control box should ...read more -
Sku: 30396Nut, #1/4in-20in Stainless Steel
Stainless steel nut used to secure the 220 volt Hot Spring heater elements (31409-BYP) to the heater housing (70192) -
Sku: 36022Strain Relief 10/3
Heater strain relief used to secure the heaters power cord to the bottom of the IQ Control boxes The strain relief prevents the cord from accidentally being disconnected from inside the control box should the cord be pulled down -
Sku: 30100Strain Relief Bushing, 1/2in
This bushing is used for strain relief of cords that are 1/2" in diameter, such as the cord for the heater in a Hotsprings, Tiger River, or LimeLight spa -
Stainless steel bolt used on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps to secure the mounting bracket to the floor in the Hot Spring equipment compartment -
Sku: 30105Romex Clamp 3/4in
This clamp is used as strain relief is used to secure the heater's power cord to the bottom of the IQ Control box The strain relief prevents the cord from accidentally being disconnected from inside the control box should the cord be pulled down -
Sku: 71742Bolt, #10 X 2-1/2in
OBSOLETE These bolts are used with washers to fasten the left and right Base Tubes on a Gliderite Illustration (# 5) on the Gliderite parts diagram -
Sku: 71217Hex Head Bolt, 1/4in-#20 X 1in
This bolt is used to fasten the Slide Lock Bar to the Side Arm -
Sku: 71614Strain Relief
This strain relief is found on most LX jet pump models -
Sku: 71613Strain Relief #3461
Strain relief #3460 -
Bolt that secures the suction flange onto the front of the Wavemaster 7000 (v 1) -
Universal Bushing, 0 875 inch, found in Hot Spot Control Box Assembly (37335) This Bushing protects the Electronic T-Stat (75089) from the metal control box housing This part can be found on the 1998 Hot Spot models -
Sku: 37752Wing Nut,10-24 Stainless Steel
This wing nut is used to hold the bulb clamp in place on the heater body in Tiger River spas from 1992 to 1994 The bulb clamp holds the copper thermostat and hi-limit bulbs to the side of the heater where they are used to monitor the temperature of the spa ...read more -
Sku: 33253Nut, Speed Narrow
Nut, speed narrow -
Hex bolt, 1/4in-20 x 1-1/2in stainless steel -
Sku: 32748Lag Bolt 3in
3in lag bolt -
Sku: 32736Nut, Lock 1/4in (Thin)
1/4in lock nut -
Sku: 30102Bushing, Snap 3/8in Outside Diameter
This bushing is used around openings through the control box used on pre-1997 Hot Springs spas where the copper tubes for the temperature probes and the cable for the spa power on light pass through -
Sku: 300859Nut, 2.5mm
This nut is used to secure the circuit board to the back of the control panel bezel on Tiger River spas from 1992-1997 It replaces a small spring clamp that used to do the same job The posts that the nut screws on to are actually plastic and are not ...read more -
Sku: 71218Bolt, #20 X 1/4in. X 2in. Hex Head
Attaches the sidearm to the pivot wheel on all spa models (except the Hot Spring Classic) -
Sku: 34029Nut 10-24 Nylon
Nut 10-24 Nyloc -
Sku: 34174Bolt, 1/4in-20 X 5/8in 100 Degree
Bolt, 1/4in-20 x 5/8in 100 degree -
This nut goes onto the volute bolt that secures the seal place to the volute -
Sku: 71188
Bolt, 3/8in-24 x 2, pack of 5
Bolt, 3/8in-24 x 2, pack of 5
Showing 1–30 of 53 results