It was very easy to select the corret parts for my "serial Number". All parts were correct and operated as required.On 06/20/2024 by M. R. (verified customer)
Hardware: Bolt, Mounting Kit, Nut, Sleeve, Spacer, Wire Joint
Showing 1–30 of 63 results
-
Sku: 73019Pillow Retainer Screw Kit
The plastic retainers in this kit come in two lengths: The short gray retainers are used if your pillows have remained in place over the years The gray extensions are used only if your pillows have fallen off often in the past -
"Blade Mount" pillow retainer (set of two blades) for all Hot Spring spa pillows and all Limelight spa pillows beginning in the second quarter of 2007 Check the diagrams for the correct pillow retainer -
Sku: 30018Mounting Bolt, Wavemaster
1/4-20 X 1-1/4" long mounting bolt that secures the pump to the floor of the equipment compartment Used on the Wavemaster 4000, Wavemaster 6000 and Wavemaster 7000 3 jet pumps -
Sku: 70035Bolt, Hex Hd 3/8in-16 X 1-3/4in, Starite
Stainless steel bolt used to secure the 1HP and 2HP Sta-rite Max-E-Glas jet pump motor to the mounting bracket in the Hot Spring equipment compartment -
Sku: 70059Bolt, #3/8in-16 X 1in Hex, Starite
Stainless steel bolt used to connect the seal plate to the electric motor on both 1HP and 2HP Sta-rite Max-E-Glas jet pumps -
Sku: 30297Nut, Volute Clamp, Starite
Used to tighten the volute clamp that binds the volute and seal plate together on all 1HP and 2HP Starite Max-E-Glas jet pumps that were used on some Hot Spring spa models prior to 1994 -
Bolt that secures the motor onto the Wavemaster 7000 (v 1) seal plate -
This bolt is used to secure the base of the 1st version Wavemaster 7000 jet pump to the motor and also secures the base to the floor of the equipment compartment -
Sku: 72574Hardware Bag #1, Cover Cradle
This Cover Cradle & Cover Cradle II hardware bag #1 includes the following: Four Hole Side Hinge (Qty 2) Four Hole Rear Hinge (Qty 2) #10 x 1" Flat Head Screws (Qty 8) #10 x 1-1/2" Flat Head Screws (Qty 8) Note: The items in this hardware bag are ...read more -
Sku: 30396Nut, #1/4in-20in Stainless Steel
Stainless steel nut used to secure the 220 volt Hot Spring heater elements (31409-BYP) to the heater housing (70192) -
Sku: 72714Hardware Bag #2, Cover Cradle II
This Cover Cradle II hardware bag #2 includes the following: 1/4"-20 x 3/4" Stainless Steel Hex Bolts (Qty 4) #10 x 1-1/2" Stainless Steel Flat Head Screws (Qty 8) #10 x 1-1/2" Stainless Steel Pan Head Screws (Qty 14) Note: The items in this hardware ...read more -
Sku: 74888-1Multizone Lighting Bayonet Sleeves
Multizone lighting bayonet sleeves, quantity of 1 -
Stainless steel bolt used on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps to secure the mounting bracket to the floor in the Hot Spring equipment compartment -
Sku: 71742Bolt, #10 X 2-1/2in
OBSOLETE These bolts are used with washers to fasten the left and right Base Tubes on a Gliderite Illustration (# 5) on the Gliderite parts diagram -
Sku: 71217Hex Head Bolt, 1/4in-#20 X 1in
This bolt is used to fasten the Slide Lock Bar to the Side Arm -
Sku: 71072Retainer Clip
Used on the 1995-1999 Hot Spring Dream Pillow Neckjet -
Bolt that secures the suction flange onto the front of the Wavemaster 7000 (v 1) -
Sku: 37752Wing Nut,10-24 Stainless Steel
This wing nut is used to hold the bulb clamp in place on the heater body in Tiger River spas from 1992 to 1994 The bulb clamp holds the copper thermostat and hi-limit bulbs to the side of the heater where they are used to monitor the temperature of the spa ...read more -
Sku: 33253Nut, Speed Narrow
Nut, speed narrow -
Hex bolt, 1/4in-20 x 1-1/2in stainless steel -
Sku: 32748Lag Bolt 3in
3in lag bolt -
Sku: 32736Nut, Lock 1/4in (Thin)
1/4in lock nut -
Sku: 300859Nut, 2.5mm
This nut is used to secure the circuit board to the back of the control panel bezel on Tiger River spas from 1992-1997 It replaces a small spring clamp that used to do the same job The posts that the nut screws on to are actually plastic and are not ...read more -
Sku: 71218Bolt, #20 X 1/4in. X 2in. Hex Head
Attaches the sidearm to the pivot wheel on all spa models (except the Hot Spring Classic) -
Sku: 34029Nut 10-24 Nylon
Nut 10-24 Nyloc -
Sku: 34174Bolt, 1/4in-20 X 5/8in 100 Degree
Bolt, 1/4in-20 x 5/8in 100 degree -
Mounting plate found on the backside of all 1994-1997 Hot Spring Classic spas control panels -
Threaded spacer with brass insert, Classic and Prodigy
-
This nut goes onto the volute bolt that secures the seal place to the volute -
Sku: 71188
Bolt, 3/8in-24 x 2, pack of 5
Bolt, 3/8in-24 x 2, pack of 5
Showing 1–30 of 63 results