It was very easy to select the corret parts for my "serial Number". All parts were correct and operated as required.On 06/20/2024 by M. R. (verified customer)
Showing 1–30 of 53 results
-
Sku: 30297
Nut, Volute Clamp, Starite
Used to tighten the volute clamp that binds the volute and seal plate together on all 1HP and 2HP Starite Max-E-Glas jet pumps that were used on some Hot Spring spa models prior to 1994 -
Sku: 72574
Hardware Bag #1, Cover Cradle
This Cover Cradle & Cover Cradle II hardware bag #1 includes the following: Four Hole Side Hinge (Qty 2) Four Hole Rear Hinge (Qty 2) #10 x 1" Flat Head Screws (Qty 8) #10 x 1-1/2" Flat Head Screws (Qty 8) Note: The items in this hardware bag are ...read more -
Sku: 77290
Panel Clip, Door/side, NXT
Door and side panel clip NXT model Highlife Collection Grandee NXT (GGN), Envoy NXT (KKN), JetsetterNXT (JJN) To remove Door/Side Panel, loosen the 2 screws on each clip below the panel Slide Door/Side Panel to the "LEFT" Door/Panel will drop ...read more -
Sku: 30099
Bushing, Strain Relief
This 3/8" strain relief is used to secure the jet pump(s), circulation pump, light and Ozonator power cords to the bottom of the IQ 2020 Control boxes The strain relief prevents the cord from accidentally being disconnected from inside the control box should ...read more -
Sku: 30396
Nut, #1/4in-20in Stainless Steel
Stainless steel nut used to secure the 220 volt Hot Spring heater elements (31409-BYP) to the heater housing (70192) -
Sku: 36586
Clip, Extruded Air Valve
Used to hold the air intake for the Freshwater II Ozonator in place on the wall in the equipment compartment near the Ozonator Found in Hotspring and Tiger River Spas with Freshwater II Ozonators -
Sku: 36022
Strain Relief 10/3
Heater strain relief used to secure the heaters power cord to the bottom of the IQ Control boxes The strain relief prevents the cord from accidentally being disconnected from inside the control box should the cord be pulled down -
Sku: 30100
Strain Relief Bushing, 1/2in
This bushing is used for strain relief of cords that are 1/2" in diameter, such as the cord for the heater in a Hotsprings, Tiger River, or LimeLight spa -
Sku: 72714
Hardware Bag #2, Cover Cradle II
This Cover Cradle II hardware bag #2 includes the following: 1/4"-20 x 3/4" Stainless Steel Hex Bolts (Qty 4) #10 x 1-1/2" Stainless Steel Flat Head Screws (Qty 8) #10 x 1-1/2" Stainless Steel Pan Head Screws (Qty 14) Note: The items in this hardware ...read more -
Sku: 73249
Panel Clips, Male and Female, QTY 4
Panel clips, male/female, for the removable panels on Hot Spring models, quantity of 4 -
Sku: 30105
Romex Clamp 3/4in
This clamp is used as strain relief is used to secure the heater's power cord to the bottom of the IQ Control box The strain relief prevents the cord from accidentally being disconnected from inside the control box should the cord be pulled down -
Sku: 73451
Hardware Bag #1, Uprite Cover Lifter
Bag #1 for the upright cover lifter Contains the following: 2 x 1/4 x 20 5/8" Hex Bolts 2 x 1/4 x 1" Fender Washers 2 x 2 Hold Deck Hinge 10 x #10 Washers 8 x #10 1/2" Square Panhead Self Tapping Screws 10 x #10 1 1/2" Square Pan Tapping Screws 12 ...read more -
Sku: 72715
Hardware Bag #3, Cover Cradle II
This Cover Cradle II hardware bag #3 is only for spas with removable exterior panels and includes the following: #10 x 2" Stainless Steel Flat Head Screws (Qty 8) #10 x 2" Stainless Steel Pan Head Screws (Qty 14) Note: The items in this hardware bag are ...read more -
Sku: 71614
Strain Relief
This strain relief is found on most LX jet pump models -
Sku: 71613
Strain Relief #3461
Strain relief #3460 -
Universal Bushing, 0 875 inch, found in Hot Spot Control Box Assembly (37335) This Bushing protects the Electronic T-Stat (75089) from the metal control box housing This part can be found on the 1998 Hot Spot models
-
Sku: 37752
Wing Nut,10-24 Stainless Steel
This wing nut is used to hold the bulb clamp in place on the heater body in Tiger River spas from 1992 to 1994 The bulb clamp holds the copper thermostat and hi-limit bulbs to the side of the heater where they are used to monitor the temperature of the spa ...read more -
Sku: 33253
Nut, Speed Narrow
Nut, speed narrow -
Sku: 32736
Nut, Lock 1/4in (Thin)
1/4in lock nut -
Sku: 30102
Bushing, Snap 3/8in Outside Diameter
This bushing is used around openings through the control box used on pre-1997 Hot Springs spas where the copper tubes for the temperature probes and the cable for the spa power on light pass through -
Sku: 300859
Nut, 2.5mm
This nut is used to secure the circuit board to the back of the control panel bezel on Tiger River spas from 1992-1997 It replaces a small spring clamp that used to do the same job The posts that the nut screws on to are actually plastic and are not ...read more -
Sku: 34029
Nut 10-24 Nylon
Nut 10-24 Nyloc -
This nut goes onto the volute bolt that secures the seal place to the volute
-
Sku: 31158
Clip, Lid Filter Grandee pre 1989
There are four filter clips (31158) and four screws (30341) to hold the filter lid in place Grandee Pre-1989 -
Sku: 78176
Panel Clip, 4 pack, Limelight
This panel clip is the bracket that is also considered the male piece for new Limelight all models 2018 and newer -
Sku: 78817
Plastic Panel Clip
Plastic Panel Clip for Limelight beginning in 2019 -
Sku: 75105
Hardware Bag #4 for Upright Cover Lifter
Hardware for the upright spa cover lifter -
Obsolete: Factory replacement suggestion item #72714 Hardware Bag #2 used on the Cover Cradle and Cover Cradle II It contains screws for mounting the cover lifter to the spa and cover All screws use Robertson (square drive) head bits
-
Sku: 30393
Nut, Brass – Cap #1/4in-20
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Nut, Brass - Cap #1/4in-20 -
Sku: 30390
Nut, Hex #10-24in
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Nut, Hex #10-24in
Showing 1–30 of 53 results