Great serviceOn 04/19/2024 by H. P. (verified customer)
Brand: Hot Spring Pre 89, Tiger River
Showing 1–30 of 45 results
-
This repair kit for the Watkins No Fault heater includes the replacement end cap for the double barrel PDR heaters which fits the Watkins Manufacturing label only This kit comes with two red seals/o-ring gaskets, replacement screws, 2 side braces and the ...read more -
Sku: 31212O-Ring, Heaterbody 115V 1.5Kw
This o-ring is used to seal the heater element (31255) into the heater housing(s) (part 10475 or 30786) -
Sku: 70108Retainer Gasket, Heaterbody 115V
The Retainer is used to hold the Heaterbody O-ring, (31212) into place on Hot Spring models only -
NOTE: It is recommended to buy the OEM O-Ring (31212) and Gasket (70108) The ones included are slightly thinner than the OEM This 1500 watt heater element is the replacement for all 1980-1994 Hot Spring spa models that operated on 115volts This heater ...read more -
This heavy-duty fiberglass-reinforced polymer split nut comes in two pieces and is designed to replace compression fitting nuts (aka pump union nuts) that have broken due to vibration, age and finally over-tightening The two halves of this fitting are held ...read more -
Sku: 70868-BYPInsulation, Heaterbody 115V
This is an alternate version of the OEM insulation which minimizes the heat loss through the heater housing The insulation is wrapped around the stainless steel heater body used in 115 volt spas made from 1980 to 1994 -
This plug has been used on the 220volt pre-1995 Hot Spring heater to cap off the drain hose by clamping the 1/4" vinyl drain tubing to the closed 1/4" nipple on this plug Also used in the 71557-BYP Kit -
Sku: 30348Screw, #10-24 X 3/4in Stainless Steel
Stainless steel screw mostly used on the 1980-1994 115volt Hot Spring heaters to secure the heater element to the heater body Four of these are used with each heater -
Sku: 30392Nut, Hex #10-24in Stainless Steel
Used on the 1980-1994 115volt Hot Spring heaters in conjunction with the stainless steel screw (30348) to secure the heater element to the heater body -
Sku: 31409-BYPHeater Element, Hot Spring, 230v 2.5kW, Pre-1995
What's Included: Heater element w/ power cord, gasket and o-ring This 230v heater element was used on the 1987-1994 Hot Spring Grandee, Highlife and 230-volt Classic and Indoor/Outdoor (later named Sovereign) models There are two heater elements located ...read more -
Stainless steel screw used to secure the heater to the equipment compartment floor on Hot Spring & Tiger River spa models Also used on the SilentFlo 5000 Circulation pump and to hold the Ozonator to the wall of the equipment compartment -
This replacement compression fitting split nut (AKA Split Union Nut-2") is used to connect heaters on the 1993-1994 Hot Spot Z, all 1998-current Hot Spot models, Solana models beginning in 2000 and all 1992-1994 Tiger River spas It is designed in two half ...read more -
Sku: 31240O-Ring, Heaterbody 230V
This o-ring is used in conjunction with the Retainer Gasket (part 70092) to seal the heater element(s)(part 31409-BYP) into the heater housing (part 70192) -
Sku: 30396Nut, #1/4in-20in Stainless Steel
Stainless steel nut used to secure the 220 volt Hot Spring heater elements (31409-BYP) to the heater housing (70192) -
Sku: 34877O-Ring, Heater Flange, Cartridge Heater
One of two o-rings used to seal the cartridge-style heater to its flange on all 1995-1996 Hot Spring & Tiger River spas and 1995-1997 Hot Spot spa models The second o-ring is a 34876 -
One of two o-rings used to seal the cartridge-style heater to the flange on all 1995-1996 Hot Spring & Tiger River spas and 1995-1997 Hot Spot spa models The other o-ring is a 34877 -
Sku: 10475-BYPHeaterbody, Hot Spring, 115V, 3/4in Ports
What's Included: Heaterbody, 115V -Stainless Steel with two 3/4" ports and one 1/4" port Description: Stainless steel heater housings with 3/4 inch ports were used on all 1990-1994 115v Hot Spring spa models The housing (heater body) is tubular in shape ...read more -
Sku: 30620Insulation, Heaterbody, 230V
The insulation surrounds the heater housing found on all 220 volt Hot Spring Spas manufactured from 1984-1994 This insulation minimizes the heat loss through the heater housing -
Sku: 70732Discharge, Heater -Tiger River
This adapter is located between the heater and jet pump on a 1992-1994 Tiger River Khyber, Manora, and Tondi spa and connects onto the small circulation pump (usually the Silentflo 5000) via a 1/2" vinyl tube -
Sku: 71539Heater Cord Adapter, 230v Tiger River
This heater cord adapter may be needed when replacing a No-Fault 5500 cartridge heater with a new PDR Heater Assembly in a 1995-1996 Tiger River 230volt wired spa model This adapter is attached to the end of the new PDR heater's power cord to enable it to ...read more -
Sku: 71538Heater Cord Adapter, 115v Tiger River
This heater cord adapter may be needed when replacing a No-Fault 1500 cartridge heater with a new PDR Heater Assembly in a 1995-1996 Tiger River Manora or Tondi spa model This adapter is attached to the end of the new PDR heater's power cord to enable it to ...read more -
Sku: 30120Lug, Grounding
Used on various components in the equipment compartment to provide a place for the grounding wire to attach to -
Sku: 35155Receptacle, Heater-230v, Hot Spring
This heater receptacle mounts into the control box on the 1995-1996 Hot Spring Grandee, Landmark, Highlife, Classic (220volt model), Sovereign (220volt model) and Summit The 220v heater (No-Fault 5500) plugs into this black receptacle on the bottom of the ...read more -
Sku: 20480Plug, Heaterbody Drain – 1/2in
This plug is for the 1989-1994 230v heater This 1/2" size if for the heaters that have a 1/2" drain hose For a 1/4" plug use the 38398 -
This 220volt heater receptacle is located in the 1995-1996, 220volt Tiger River Manora & Tondi control box It provides a place to plug in the heater Over the years, this item can fatigue and require replacement For the 120volt receptacle see part 35114 -
Sku: 70095Cord Adapter, 230Volt, Hot Spring
This heater cord adapter allows one to plug the current replacement heater element into the older style Hot Spring control box -
Sku: 37752Wing Nut,10-24 Stainless Steel
This wing nut is used to hold the bulb clamp in place on the heater body in Tiger River spas from 1992 to 1994 The bulb clamp holds the copper thermostat and hi-limit bulbs to the side of the heater where they are used to monitor the temperature of the spa ...read more -
Sku: 30171Heater Receptacle, 220v. Hot Spring
Used on the 1989 Hot Spring 220volt models The Grandee, Highlife, Sovereign IH and Classic FH -
Sku: 37726Heater Housing Tail Piece, 2in x 1 1/2in
This is a heater tailpiece for a 2-inch heater housing The tailpiece is designed to accept a 1 1/2" PVC pipe or a 1 1/2" male PVC fitting The connection should be made using PVC cement and primer -
On Backorder at the factory for the past 12 months Call to speak to one of our techs regarding the alternative insulation 70868-BYP we have available 805-541-9000 This insulation minimizes the heat loss through the heater housing The insulation ...read more
Showing 1–30 of 45 results