Best place ever, always goodOn 05/31/2024 by M. D. (verified customer)
Find all the plumbing parts you need here. Flexi PVC tubing, Vinyl Tubing, Elbows, Tees, Diverter Valves, Levers & Bezels, Check-Valves, Couplers, and more.
Showing 1–30 of 31 results
-
Sku: 74078
Injector, Freshwater Ozone, Black
The injector fits in-line after the Silentflo 5000 (discharge side and after the heater) This Kynar plastic "venturi" injector is ozone resistant and is used with the Freshwater III High Output Ozonator by Watkins manufacturing, item 72602 -
Sku: 74077
Injector, Freshwater Ozone, Red
This red ozone injector was used with the Freshwater I & Freshwater III (for Hot Spot & Solana spas) It is designed to allow a pre-determined amount of ozone bubbles per minute to enter the spa's circulating system The injector is matched to the ...read more -
Sku: 34447-x2-BYP
Compression Fitting O-rings, for 2 inch Union (Qty of 2)
(Quantity of 2 o-rings) O-rings used on the pumps 2" compression fittings ( 71036 ) found on most Hot Spring, Tiger River, Limelight, Hot Spot and Solana spa models Also used on the replacement "Wet End" pump kits and some heaters The 2" measurement refers ...read more -
O-ring used on the 2" compression fittings (71036) on most Hot Spring, Tiger River, Hot Spot, and Solana spa models The 2" measurement refers to the inner diameter of the most narrow part of the compression fitting/union The o-ring that is included measures ...read more
-
Sku: 71036
Compression Fitting, 2in with O-Ring
This 2" compression fitting, which includes the o ring, is sometimes referred to as a pump union or compression coupling It is found on the suction side of most Wavemaster® XP2 or XP2e Series Jet Pumps Other compression fittings are the 71038 and 71037 ...read more -
Sku: 30237-x2-BYP
Compression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 71038
Compression Fitting, 1-1/2in with O-Ring
This 1-1/2" compression fitting, which includes the o ring, is sometimes referred to as a pump union or compression coupling It is found on the suction and/or discharge side of FMHP/CP Series Wavemaster® Jet Pumps 2" x 1-1/2" Compression Fitting click ...read more -
This 2" compression fitting, which includes the o ring, is sometimes referred to as a pump union or compression coupling 1-1/2" Compression Fitting 2" Compression Fitting
-
This heavy-duty fiberglass-reinforced polymer split nut comes in two pieces and is designed to replace compression fitting nuts (aka pump union nuts) that have broken due to vibration, age and finally over-tightening The two halves of this fitting are held ...read more
-
Sku: 37704
Diverter Body, 2-Port
This is a replacement valve body for 1994-2008 Hot Spring, Tiger River and all Limelight spa models with two-port diverter valves This valve body has 2" diameter ports and replaces the original black valve body -
Sku: 37297
6 Port Diverter Valve Body
This 6 port diverter valve body is used on the Hot Spring and Tiger River spa models that utilize a four-position valve -
This replacement compression fitting split nut (AKA Split Union Nut-2") is used to connect heaters on the 1993-1994 Hot Spot Z, all 1998-current Hot Spot models, Solana models beginning in 2000 and all 1992-1994 Tiger River spas It is designed in two half ...read more
-
Sku: 72072-1.5
Split Nut for 1.5in Compression Fittings
This 1-1/2" split nut comes in two pieces and is designed to replace compression fitting nuts (aka pump union nuts) that have broken due to vibration, age, and over-tightening The two halves of this fitting are held together by two screws -
Sku: 31309
Valve Body, Air Control
Air control valve body used on all Hot Spring spas from 1989-mid 1993 This part is found under the bar top on the backside of the spa shell It is sealed to the bottom of the bar top using an o-ring so that water splashed on it does not leak into the ...read more -
Sku: 30502
Diverter Valve Body, 1-1/2in
Replacement valve body for Hot Spring spa models manufactured prior to 1994 This gray valve body has 1-1/2" diameter ports This valve body typically sits above the jet pump for diverting water from one area of the spa to the other Use with Valve Insert ...read more -
Sku: 30548
Starite Compression Fitting, 1-1/2″
1-1/2" compression coupling assembly (pump union) for all Starite pumps used on Hot Spring spas -
Sku: 33838
Valve Body, Air Control
This is part of the air control valves used on Hotspring and Tiger River spas from 1999 to 2003 It is where the moving portion of the valve resides and where the plumbing connects to the valve, as well as provides a way to mount the valve to the shell of ...read more -
This compression fitting (aka pump union, quick disconnect, coupling) is used on the discharge side of the Tiger River Wavemaster Pumps to ensure that the small Silentflo 5000 or 5002 circulation pump pulls water through the filter when the jet pump is off ...read more
-
Sku: 71387
Fitting, Comp 45 Degree with O-Ring
This is a 2" pump union with a 45 degree offset street fitting It is used to connect the jet pump to the plumbing of the spa and allows the plumbing to come towards the pump from a 45-degree angle It glues into a 2" female PVC slip fitting using PVC ...read more -
Sku: 75124
Comfort Control Valve Body Socket
Socket for the Comfort Control (aka air control valve) -
Sku: 74836
Comfort Control Valve Body
Comfort Control Valve Body (aka air control) for the Hot Spring, Tiger River and Limelight spa models beginning in 2009 Check your serial number in the Parts Finder to be sure this part is for your spa -
Sku: 74350
Red Ozone Injector FreshWater III
Ozone Injector assembly including tubing and check valve for Hot Spot and Solana model spas without dedicated circulation pumps This injector is designed for when a 2-speed jet pump is used to circulate the water through the heater -
Sku: 74833
Comfort Control Valve Body Nut
Nut that holds the 2009 Comfort Control (aka air control valve) body in place -
Sku: 39314
Ozone Injector, Freshwater 1
This red ozone injector is used in conjunction with the Freshwater I Ozonator It designed to allow a pre-determined amount of ozone bubbles per minute to enter the spa's circulating system -
Sku: 72231
Air Injector Assembly
Air injector -
Sku: 30550
Starite Compression Fitting, 1-1/2in
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com 1-1/2" compression coupling assembly (pump union) for all 1-1/2" Starite pump volutes Sta-Rite pumps ...read more -
Sku: 71075
Injector, Freshwater Ozone, Cut End
Obsolete: Factory replacement suggestion item #74078 Ozone injector for the FreshWater II ozonator -
Sku: 35283
Compression Fitting O-Ring, Wavemaster 7000 V2, and 9000
This item is obsolete and replaced by:
34447Obsolete: Factory replacement suggestion item #34447 O-Ring Compression fitting o-ring (pump union) for all the Wavemaster 7000 (v 2) & Wavemaster 9000 (v 1) jet pumps -
Sku: 37489
6 Port Diverter Valve Core
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com 6 Port Diverter Valve Core
Showing 1–30 of 31 results