I would like to express how excellent this company is. I inherited a house with a 2007 Hotspring Aria hot tub. The spa hasn’t been operated in years and when I turned it on, it ran for about 10 minutes and died. I mean dead died. I knew absolutely nothing about hot tubs but with the excellent diagnosis videos, installation videos and superior phone support, I was able to replace the main control board, heater relay board, heater, circulation pump, the ozonator and all associated tubing. This took 4 1/2 hours over two days (I had to watch videos) but the spa runs like new! I had one question regarding the jumper voltage 18 or 12. I spoke with a technician and he was able to answer my question as well as helping me double check the voltages for the components on the relay board. I am handy with electronics and electricity and am comfortable working with 230 volts. Shipping was fast and as expected. I highly recommend BackYardPlus.On 06/28/2024 by F. R. (verified customer)
Plumbing: Adapter, Barbed Adapter, Check Valve, Ring, U Ben, Wallfitting
Showing 1–30 of 58 results
-
Sku: 31417Adapter, 3/4in Barbed X 3/4in Slip
This barbed fitting is primarily used to connect 3/4" vinyl tubing to various places within the circulating/heating system of Hot Spring & Tiger River from 1990 forward This PVC fitting is often found glued into a 90-degree elbow rising from the floor of ...read more -
Sku: 34504Adapter, 3/4in Sp X 1/4in Sp
This adapter glues into a 3/4" female PVC slip fitting using PVC primer and cement and accepts a 1/4" vinyl hose that can be secured using PVC cement as well or a hose clamp -
Sku: 72701Hartford Loop Assembly
This retrofit kit is used to replace the air check valve that was used in some Hot Spring spa models This kit replaces the obsolete 72342 Check your serial number in the parts finder above to be sure this part is for your spa -
Sku: 30703Adapter, 3/4in X 3/4in Mht X Slip
This PVC fitting glues on to a 3/4" male PVC rigid or flexible pipe and allows a 3/4" female pipe thread to connect to it On Hotsprings and Tiger River spas, it's used as part of the drain system, to allow a garden hose to be connected and water to be ...read more -
Sku: 30490Wallfitting, Rear
This fitting is used on many different Hot Spring spa models in various places including the grill style filter compartment as part of the filter assembly Also used in the filter compartment of all 1992-1996 Tiger River spa models -
This coupling is made from an ozone resistant plastic called Kynar It is connected to the side of the newest style of Freshwater III Ozonator, 72602 The ozone tubing connects onto this barbed fitting If your barbed fitting breaks off, this factory ...read more -
Sku: 70864Check Valve, Safety Suction
This check valve's function is to "open" when someone puts their hand over the jet pumps suction fitting within the filter intake This check valve will "open" drawing air into it from the equipment compartment, thereby stopping suction of the jet pump This ...read more -
This barbed fitting is primarily used to connect 1/2" vinyl tubing to various places within the circulating/heating system or jets in a Hot Spring & Tiger River spa It simply glues into a 1/2" PVC coupling or elbow with regular PVC cement -
Sku: 010009Barbed adapter 1 in x 3/8 Spigot
Barbed adapter 1 inch by 3/8 inch 425-5010 BARB ADAP 1IN(1)3/8IN -
This threaded wall fitting is located in the bottom of the filter compartment on all 1997-2010 Tiger River Bengal, Caspian, Sumatran & Siberian spa models This is where the filter standpipe screws into -
Barbed adapter which is 1/2" male threads on one end and 1/2" barbed on the other -
This barbed fitting is primarily used to connect 1/2" vinyl tubing to various places within the circulating/heating system of Hot Spring spa models -
Sku: 30586Barbed Adapter, 1/4in X 5/16in
This barbed adapter is used in various places but primarily in the Moto-Massage niche for the small silicone Moto-Massage Jet air tube to slip onto on pre-1997 Hot Spring spa models -
Sku: 71128Wallfitting, Drain Drilled
Wall fitting, rear drain, 1/2" drilled, Hot Spring Rear wall fitting located in the footwell of the spa Front wall fitting part 30488 -
Sku: 70846Connector 3/4in X 1/2in Barbed X Barbed
Connector, 3/4in X 1/2in, barbed X barbed Connects a 3/4" tube to a 1/2" tube -
Sku: 31556Adapter, 1/4in X 1/4in Spig X Slip
Adapter, Barb x Socket, 1/4" x 1/4" -
This compression fitting (aka pump union, quick disconnect, coupling) is used on the discharge side of the Tiger River Wavemaster Pumps to ensure that the small Silentflo 5000 or 5002 circulation pump pulls water through the filter when the jet pump is off ...read more -
Sku: 31348Adapter, 1-1/2in Mipt
This male adapter screws into a 1-1/2" jet pump volute in order for a 1-1/2" compression coupling (pump union) to screw onto the adapter -
PVC elbow that allows a 3/4" barbed fitting and a 3/4" threaded fitting to be connected together Both fittings are male, and the barbed fitting should be secured using hose clamps, and the threaded fitting should be wrapped in Teflon tape before installing ...read more -
Sku: 39438Adapter, Ell 1/2in Hose X 1/4in Mpt
Adapter, barbed ell, PVC, 1/2" hose x 1/4", male pipe thread -
Sku: 30690Adapter, 3/8 X 1/2 Mipt X Fipt
This adapter Used with the 30118 thermostat cord grip -
Barbed adapter which is 3/4" male threads on one end and 1/2" barbed on the other -
Sku: 30702Adapter, 3/4in X 1/2in Mht X Slip
This PVC fitting accepts a 1/2" male slip fitting or 1/2" PVC pipe and should be attached using PVC primer and cement The other end is a 3/4" male pipe thread and can be used to connect fittings such as a garden hose This part is used commonly in the ...read more -
Sku: 301035Barbed Adapter, 432-007525
Barbed adapter -
Sku: 75010Inlet Assembly with Check Valve
The four pieces of this pump inlet assembly come pre-assembled and include the check valve This assembly was used on the jet pump on the 1989 Hot Spring Jetsetter, Prodigy, and Sovereign Also used on the 1991-1992 Grandee -
Sku: 71263Wallfitting, Gray, without Knockout
Gray wallfitting, for Hot Spring -
This is a PVC adapter that has 1/2" male threads on one end and 3/8" barbed on the other Allows a 1/2" female fitting to be adapted to 3/8" tubing that has no fitting on the end -
Sku: 38507U-BEN 2X2 SS (429-4030)
Used for jet pump plumbing on various models -
Sku: 31486Adapter, 3/4in Slip
Adapter, Barb x Socket, 3/4" x 3/4" -
2" X 1-1/2" male adapter commonly used on the suction side of pumps
Showing 1–30 of 58 results