I find backyard plus sort of amazing.. Whenever I have a problem with my 18 year old tub (which is about ever 9 months or so) I can almost always go here and find parts. They describe how to troubleshoot to verify that this part might be broken and provide great videos on how to replace. When I jumped in the tub a few weeks back (and then jumped right out... it was cold!) I didn't hesitate, tracked down this part... verified it was a replacement and ordered it. Two days later I replaced it (my old board looked fine from the front but when I pulled it off you could see the charring on the back) and now the hot tub it happily working again! They are amazon-like in how fast they ship, have great support (the few times I had to call in with a question) and provide great example videos and written documentation -- if you are AT ALL handy you can totally maintain the hot tub yourself and backyard plus is a great partner. Regarding this specific part -- I had a 2006 model and the board was a different design but 100% fit with no problems -- The thing to test is ifs your HTR led is on there should be voltage (128v AC in my case) switched to the heater unit (the cables to the left of the board) -- mine registers about 2v AC so I suspected it was this board. As I mentioned when I replaced it you could see the charring on the backside and the new board is now happily working great.On 04/08/2024 by J. M. (verified customer)
Showing 31–52 of 52 results
-
Elbow, 1/4in x 1/4in male iron pipe threaded (Mipt) x slip
-
Sku: 31401
Elbow, Reducing, 2in X 1-1/2in
Reducing Ell, 90-degree, PVC, 2" X 1-1/2" -
Sku: 31107
Elbow, 1-1/2in Spigxspig
This PVC elbow is used on the jet pump inlet of many earlier models of Hotspring spas It will connect to a 1 1/2" female PVC slip connector on either end of it It often is tapped with a 1/4" barbed fitting for a bleedline (Part number 30598) -
Sku: 30658
Elbow 45 Degree 1-1/4in Slip X Slip
This elbow is used to join two 1 1/4" male PVC slip fittings or 1 1/4" rigid or flexible PVC pipes together at a 45-degree angle PVC primer and cement should be used to secure this fitting to the fittings it is joining together -
Sku: 30657
Elbow, 45 Degree 1in Slip X Slip
This elbow is used to join two 1" male PVC slip fittings or 1" rigid or flexible PVC pipes together at a 45-degree angle PVC primer and cement should be used to secure this fitting to the fittings it is joining together -
Sku: 30655
Elbow, 45 degree 1/2in Slip X Slip
This elbow is used to join two 1/2" male PVC slip fittings or 1/2" rigid or flexible PVC pipes together at a 45-degree angle PVC primer and cement should be used to secure this fitting to the fittings it is joining together -
Elbow, St 90-degree 1-1/2" male iron pipe thread x slip
-
This is a 90-degree elbow, made of PVC, and is made to accept a 1/2" female pipe threaded fitting on one side of the elbow And on the other side, it will accept a bare PVC pipe or male PVC slip fitting
-
This is a 90-degree elbow, made of PVC, and is made to accept a 1/2" male pipe threaded fitting on each side of the elbow The fitting should either have Teflon tape wrapped on the threads, or use some sort of pipe thread adhesive, or sealer
-
This is a 90-degree elbow, made of PVC, and is made to accept a 3/4" male pipe threaded fitting on each side of the elbow The fitting should either have Teflon tape wrapped on the threads, or use some sort of pipe thread adhesive, or sealer
-
Sku: 30644
90 Degree Elbow 1in Slip X Slip
This elbow is used to join two 1" male PVC slip fittings or 1" rigid or flexible PVC pipes together at a 90-degree angle PVC primer and cement should be used to secure this fitting to the fittings it is joining together Reference: 406-010, D2466, ...read more -
Sku: 30641
Elbow, 90 Degree 3/8in Slip X Slip
This elbow is used to join two 3/8" male PVC slip fittings or 3/8" rigid or flexible PVC pipes together at a 90-degree angle PVC primer and cement should be used to secure this fitting to the fittings it is joining together -
Sku: 30614
Elbow, 1/2in Barb X 1/2in Threaded
PVC elbow that allows a 1/2" barbed fitting and a 1/2" threaded fitting to be connected at a 90-degree angle Both fittings are male, and the barbed fitting should be secured using hose clamps, and the threaded fitting should be wrapped in Teflon tape ...read more -
This elbow adapts a 1/2" female pipe thread fitting to a 1/2" male barbed fitting So a male pipe thread fitting can be attached to one side of the elbow, and 1/2" tubing on the other side
-
Sku: 34145
Side Outlet Elbow, Hot Spot Z
Side outlet elbow, Hot Spot Z -
Sku: 34364
Elbow, Spigot X Slip Manifold
Elbow, spigot x slip manifold -
Sku: 36296
Ell 3/8in barbed x 1/2in Slip
Ell, 3/8in barbed x 1/2 slip -
Sku: 302364
3/4 IN Check Valve
3/4" check valve found on many Hot Spring models beginning in 2007, Hot Spot beginning in 2019, and Limelight models beginning in 2019 -
Sku: 300947
Reducing Elbow 1 In X 1/2 In
Reducing elbow 1 inch by 1/2 inch for Hot Spot models beginning in 2003, Hot Spring models beginning in 2007, and Limelight models beginning in 2008 -
Sku: 36954
Reducing Elbow, 1 Inch x 3/4 Inch
Reducing elbow 1 inch by 3/4 inch for various models and applications -
Sku: 72727-BYP
Elbow, 3/4in X 3/4in Barbed with 1/4in Barbed Nipple
This item is obsolete and replaced by:
77427This 3/4" elbow with a 1/4" barbed nipple coming off of the curve of the elbow is most often found on the suction side of the Silentflo 5000 and 5002 circulating pumps The 3/4" x 3/4" x 1/4" bleed line fitting has a 1/4" nipple (30598) for the 1/4" vinyl ...read more -
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com This is a 90-degree elbow, made of PVC, and is made to accept a 1/2" male pipe threaded fitting on one ...read more
Showing 31–52 of 52 results