Best place ever, always goodOn 05/31/2024 by M. D. (verified customer)
Get Watkins Wavemaster Pumps, Circulation Pumps, Wet-end Kits, Impellers, Shaft Seals, O-rings, Compression Fittings, and other parts related to your pumps.
Showing all 12 results
-
This is the complete circulation pump retrofit kit for Hot Spot SX tubs beginning in 2020 and Hot Spot TX tubs beginning in 2021 What's included: A Frog Bypass Assembly B Circulation Pump to Heater Inlet Assembly B1 2" Heater Inlet Conector with ...read more
-
This is the complete circulation pump retrofit kit for Hot Spot TX 2020 ONLY What's included: A Frog Bypass Assembly B Circulation Pump to Heater Inlet Assembly B1 2" Heater Inlet Conector with 3/4" barb fitting B2 1/4" Clear Vinyl Hose ...read more
-
Sku: 48WUA-WR3536
Wear Ring, Watkins Wavemaster Jet Pump, 48 Frame, Vendor Code 3536
This wear ring works on the 48 frame version of the Watkins Wavemaster jet pumps that have a vendor code of 3536 or have a model number that ends in "-03" Only replace your wear ring if you are replacing your impeller Only replace your wear ring if you are ...read more -
Sku: 56WUA-WR3536
Wear Ring, Watkins Wavemaster Jet Pump, 56 Frame, Vendor Code 3536
This wear ring works on the 56 frame version of the Watkins Wavemaster jet pumps that have a vendor code of 3536 or have a model number that ends in "-03" Only replace your wear ring if you are replacing your impeller Only replace your wear ring if you are ...read more -
Sku: SK-WM-7000-V3-BYP
Complete Seal Kit, Wavemaster 7000 (ver.3)
Wet End Seal Kit for the Wavemaster 7000 (ver 3) Jet Pump These parts only fit the pumps with a vendor number ending in 4081 All the replacement parts necessary when opening up the "wet end" to cure a leaking pump Since the impeller typically breaks when ...read more -
Sku: 71409
Wear Ring, Wavemaster
The jet pump wear ring keeps water from back flowing around the impeller which would reduce the jet pressure significantly It fits inside the "wet end" and slides over the impeller with the ridge side farthest away from the front of the impeller (i e , ...read more -
Sku: 70220
Wavemaster Wear Ring
The jet pump wear ring keeps water from back flowing around the impeller which would reduce the jet pressure significantly It fits inside the "wet end" and slides over the impeller with the ridge side farthest away from the front of the impeller (i e , ...read more -
Sku: 71409-E
XP2E Wear Ring
This is the XP2E wear ring for the after-market impellers 71406-SW, 71405-SB and 71404-SY Please check the dots at the end of your impeller Item 71406-SW (Silver, White), item 71405-SB (Silver, Blue) and item 71404-SY (Silver, Yellow) -
This o-ring fits onto the front of the diffuser on the Wavemaster 7000 (v 1) jet pump and also between the suction flange and the suction cover on the front of the pump
-
This heavy-duty fiberglass-reinforced polymer split nut comes in two pieces and is designed to replace compression fitting nuts (aka pump union nuts) that have broken due to vibration, age and finally over-tightening The two halves of this fitting are held ...read more
-
Sku: 72072-1.5
Split Nut for 1.5in Compression Fittings
This 1-1/2" split nut comes in two pieces and is designed to replace compression fitting nuts (aka pump union nuts) that have broken due to vibration, age, and over-tightening The two halves of this fitting are held together by two screws -
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com The suction flange bolts onto the suction cover (front) of the Wavemaster 7000 (v 1) jet pump
Showing all 12 results