On 12/29/2023 by J. M. (verified customer)
Brand: Hot Spring Pre 89, Wavemaster 3000
Showing 91–120 of 153 results
-
Sku: 10408Receptacle, Jet Pump, Hot Spring
This jet pump receptacle mounts into the control box to provide an outlet to plug in the jet pump's power cord on the 1990-1996 Hot Spring Classic, Grandee, Highlife, Jetsetter, Prodigy & Sovereign spa models -
Wavemaster 7000 (v 1) suction cover (volute) is the front half of the "wet end" (suction side) It has a square flange that accepts the adapter to connect to the plumbing of the spa Used on Hot Springs spas from 1993 to 1996 -
Sku: 70407GSKTVolute Suction Flange Gasket, Wavemaster 7000 (v.1)
Wavemaster 7000 (v 1) suction flange gasket This gasket fits between the volute cover and the square suction flange that accepts the adapter to connect to the plumbing of the spa Used on Hot Springs spas from 1993 to 1996 -
Sku: 72461Power Cord, Wavemaster, 2-Speed
This power cord is a 14/4 (60" long) with flag terminals on both ends The cord has four wires inside which are BLACK, RED, WHITE, GREEN and is used on the two speed Wavemaster Jet Pumps -
Sku: 30225Start Capacitor, Starite 1HP
Start capacitor used on all Sta-rite 1Hp Max-E-Glas jet pumps found on pre-1994 Hot Spring Grandee, Classic, Indoor/Outdoor, and Sovereign spa models -
Lock washer for the diffuser screw on a Wavemaster 7000 (ver 2) and Wavemaster 9000 jet pump -
Sku: 70126Pump Mounting Bracket, Starite 2HP
Pump mounting bracket used to secure the 2HP Sta-rite Max-E-Glas jet pump to the floor of the Hot Spring equipment compartment -
Sku: 70031Pump Mounting Bracket, Starite 1HP
Pump mounting bracket used to secure the 1HP Sta-rite Max-E-Glas jet pump to the floor of the Hot Spring equipment compartment -
Sku: 70885Power Cord, Wavemaster 3000
1995-1997 Hot Spot spas 40" replacement power cord (cord set) for the Wavemaster 3000 Jet Pump This cord set has the correct Molex end connector to enable the Wavemaster 3000 Jet Pump to plug into the control box on all 1995-1997 Hot Spot models -
Sku: 70946Impeller Screw, Wavemaster 9000
This stainless steel screw holds the impeller onto the Wavemaster 9000 jet pump shaft -
Flat Volute washer for the Wavemaster 7000 version 2 and he Wavemaster 9000 -
Sku: 73740Leak Detection Kit
For Technicians Only Leak detection kit for Hot Spring, Hot Spot, and Limelight models -
Sku: Ceramic-Disk-BYPCeramic Pump Seal Disk
This ceramic piece is part of most pump seal kits -
Sku: 71400Motor, 1.5Hp, XP
This is a replacement motor for a Wavemaster 5000 used on Tiger River and Hotsprings spas It can be wired 110 volts or 220 volts and is a single speed motor Will accept 48y frame wet ends -
Sku: 70959Base, Wavemaster 9000
Black plastic base that serves two purposes: The first is to support the pump & motor and the second is to secure the base to the equipment compartment floor If you have a 48 frame pump, you will need the rubber pad 70958 that inserts/sits in the plastic ...read more -
This hex screw runs through the flange of the motor into the seal plate on a Wavemaster 7000, second version and a Wavemaster 9000 jet pump They are used to hold the seal plate in place against the motor -
This stainless steel screw secures the diffuser to the seal plate on the Wavemaster 7000 second version and the Wavemaster 9000 jet pump -
Sku: 70826Cordset, Wavemaster 3000 Pump Hot Spot Z
This is a 12" power cord with the correct red connector, on the end, for a 1993-1994 Hot Spot Round (Z model) -
Bolt that secures the suction flange onto the front of the Wavemaster 7000 (v 1) -
Sku: 70121Run Capacitor, Starite 2HP
Run capacitor used on all 2HP Starite Max-E-Glas jet pumps on Hot Spring spas -
Sku: 30549Union, 1-1/2in Slip x Threaded
Union, 1-1/2in slip x threaded -
This screw is used to secure the volute to the pump base 70959 -
Sku: 70958Rubber Motor Pad, Wavemaster 9000
Rubber pad between the motor and the base to keep vibrations to a minimum It's used with item 70959 plastic pump base If you use a 48 frame pump, you need this rubber pad to fill the gap that is left between the motor and the base If you have a 56 frame ...read more -
One of two volute washers on the Wavemaster 7000 (second version) and the Wavemaster 9000 jet pump -
This nut goes onto the volute bolt that secures the seal place to the volute -
Sku: 77820
Pump Shroud
Pump shroud for 72991 jet pumps with vendor number 3536 -
Sku: 56WUA500-VWavemaster 9000/9200, 8000/8200 Volute O-Ring
LX MODEL O-RING Replacement volute o-ring (largest o-ring) for the Wavemaster pumps with vendor number 3536 (LX) This o-ring fits the 56-frame LX wet ends item 77713 and 77712 -
Sku: 48WUA-V
Wavemaster Volute O-Ring
LX MODEL O-RING Replacement volute o-ring (largest o-ring) for the Wavemaster pumps with vendor number 3536 (LX) This o-ring fits the 48-frame LX wet ends item 77711, 77710, and 77709 Stamped on wet-end: PP-GF30; B436-14 (03) Reference models (see ...read more -
Sku: 70032Seal Plate, Starite
This Sta-rite seal plate is the part of the "wet end" that bolts onto the pump motor This seal plate is the replacement for both the 1hp and 2hp Starite Max-E-Glas jet pumps used on Hot Spring models prior to 1993 Note: Includes a new shaft seal and ...read more -
Sku: 70071Insert, Seal Plate, Starite
Copper insert (heat sink) used on all 1HP and 2HP Starite Max-E-Glas jet pumps on Hot Spring spas Use with 30224 shaft seal
Showing 91–120 of 153 results