On 04/15/2024 by R. D. (verified customer)
Brand: Hot Spring Pre 89, Wavemaster 3000, Wavemaster 4000
Showing 61–90 of 201 results
-
Sku: 72461-BYPPower Cord, After-Market, 2-Speed, 60″
This power cord is a 14/4 (60" long) with flag terminals on both ends The cord has four wires inside which are BLACK, RED, WHITE, GREEN and is used on the two speed Jet Pumps -
Sku: ML-1OZ-BYPSilicone Grease, 1 oz. Tube
Silicone grease ideal for lubricating o-rings -
Sku: 71409-EXP2E Wear Ring
This is the XP2E wear ring for the after-market impellers 71406-SW, 71405-SB and 71404-SY Please check the dots at the end of your impeller Item 71406-SW (Silver, White), item 71405-SB (Silver, Blue) and item 71404-SY (Silver, Yellow) -
Sku: 30215-Motor-BYP1HP Starite Energy Effiecient Motor
The is the energy efficient replacement motor for the 1hp Sta-Rite pump used in some pre-1994 Hot Spring spas This motor was discontinued by Hot Spring and comes from another vendor -
Sku: 31239-Motor-BYPMotor Only, Sta-rite 2hp
This motor replaces the two horsepower single speed energy efficient motor used on the 2HP Sta-Rite pump found on the 1989-1993 Hot Spring Highlife The "wet end" only your existing pump can be installed on this replacement motor If you require the entire ...read more -
Sku: 36070-Motor-BYPMotor, 1HP, 36070 Pump
This electric motor is the energy efficient replacement motor for the Wavemaster 7000 (v 1) jet pump used on the 1993-1996 Hot Spring Classic, 1993-1995 Hot Spring Grandee and Sovereign spa models -
This is the largest o ring on the Wavemaster 7000 (v 1) jet pump It fits between the cover and the seal plate -
Sku: 30217Volute, Starite
This Sta-rite volute is the front part of the "wet end" of the 1HP and 2HP Max-E-Glas jet pumps used on the Hot Spring spa models prior to 1993 -
Sku: 30223Impeller, 1Hp Starite
Impeller for the 1hp Sta-rite used in Hot Spring spas prior to 1993 -
Sku: 70035Bolt, Hex Hd 3/8in-16 X 1-3/4in, Starite
Stainless steel bolt used to secure the 1HP and 2HP Sta-rite Max-E-Glas jet pump motor to the mounting bracket in the Hot Spring equipment compartment -
Sku: 70059Bolt, #3/8in-16 X 1in Hex, Starite
Stainless steel bolt used to connect the seal plate to the electric motor on both 1HP and 2HP Sta-rite Max-E-Glas jet pumps -
Diffuser screw washer used in addition to the diffuser screw that secures the diffuser in place on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps used on Hot Spring models prior to 1993 -
Sku: 70036Diffuser Screw, #8-32 X 7/8in, Starite
Diffuser screws used to secure the diffuser in place on the 1HP and 2HP Sta-ite Max-E-Glas jet pumps used on Hot Spring models prior to 1993 -
Sku: 70396Washer, Flat 3/8in Wavemaster
Flat 3/8in washer -
Sku: 30219Volute Clamp, Starite without Nut
This stainless steel volute clamp is used to bind the volute and seal plate together on all 1HP and 2HP Starite Max-E-Glas jet pumps that were used on Hot Spring spa models -
Sku: 30222Sta Rite Diffuser O-Ring
Diffuser o-ring for the 1hp & 2hp Sta-rite jet pumps used in Hot Spring models prior to 1993 -
Sku: 30297Nut, Volute Clamp, Starite
Used to tighten the volute clamp that binds the volute and seal plate together on all 1HP and 2HP Starite Max-E-Glas jet pumps that were used on some Hot Spring spa models prior to 1994 -
Sku: 70032-SPSeal Plate only
This after-market (Sta-rite) seal plate is the part of the "wet end" that bolts onto the pump motor This seal plate is the replacement for both the 1hp and 2hp Starite Max-E-Glas jet pumps used on Hot Spring models prior to 1993 Note: DOES NOT INCLUDE ...read more -
Sku: 70400-BYPShaft Seal, Wavemaster 7000 (v.1)
This shaft seal is for the Wavemaster 7000 (v 1) Sta-rite 5/8" shaft seal used on the 1HP and 2HP jet pumps that were built from 1998 forward This seal is used with the seal plate that DOES NOT require the copper heater sink If you are repairing a pump ...read more -
Sku: 30224Starite Shaft Seal
Sta-rite shaft seal used on the 1HP and 2HP jet pumps that use a copper heat sink on Hot Spring spas Reference number: U109-93SS -
Sku: 70120-BYPImpeller, 2Hp Starite
After Market replacement Sta-rite impeller for the 2Hp pumps used on the Hot Spring Highlife prior to 1992 -
Sku: 30220Volute O-Ring, Starite
Volute O-ring used on the Sta-rite 1HP and 2HP Max-E-Glas jet pump on Hot Spring spa models prior to 1993 -
Bolt that secures the motor onto the Wavemaster 7000 (v 1) seal plate -
This bolt is used to secure the base of the 1st version Wavemaster 7000 jet pump to the motor and also secures the base to the floor of the equipment compartment -
This o-ring fits onto the front of the diffuser on the Wavemaster 7000 (v 1) jet pump and also between the suction flange and the suction cover on the front of the pump -
This heavy-duty fiberglass-reinforced polymer split nut comes in two pieces and is designed to replace compression fitting nuts (aka pump union nuts) that have broken due to vibration, age and finally over-tightening The two halves of this fitting are held ...read more -
Sku: 77427Bleedline Fitting, Circulation Pump
Circulation Pump Bleedline Fitting This special Tee fitting includes 2 X 3/4" barbed fittings, as well as a 1/4" connection No PVC Glue needed and no assembly required like the 72727-BYP (Elbow, 3/4in X 3/4in Barbed with 1/4in Barbed Nipple) -
Largest o ring on the Wavemaster 7000 second version and the Wavemaster 9000 jet pump seal plate -
This is the after-market 3/4" Replacement Shaft Seal for the Wavemaster 7000 version 2 and the Wavemaster 9000 -
Sku: 71030Shaft Seal, Wavemaster 7000 (version 2) and 9000
This item is obsolete and replaced by:
71030-BYPReplacement Shaft Seal for the Wavemaster 7000 version 2 and the Wavemaster 9000 See item 71030-BYP for after-market shaft seal
Showing 61–90 of 201 results