The team here is amazing. Hard to get great technical support but these folks have delivered for years on excellent customer support!On 03/19/2024 by J. T. (verified customer)
Brand: Tiger River, Wavemaster 9000
Showing 61–90 of 131 results
-
Sku: 30237-x2-BYPCompression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 71038Compression Fitting, 1-1/2in with O-Ring
This 1-1/2" compression fitting, which includes the o ring, is sometimes referred to as a pump union or compression coupling It is found on the suction and/or discharge side of FMHP/CP Series Wavemaster® Jet Pumps 2" x 1-1/2" Compression Fitting click ...read more -
Hot Spring, Hot Spot & Solana spas only This barbed nipple screws into the front (suction cover) and is used on all Wavemaster Jet Pumps as well as the Sta-Rite 1Hp & 2Hp jet pumps on everything but Tiger River spas which use a 33732 nipple The ...read more -
For Tiger River and Limelight spas only This 1/2" barbed adapter fitting is located on the front of Wavemaster Jet Pumps on Tiger River and Limelight spas Teflon tape should be used on the threads of this fitting for installation -
Sku: 30018Mounting Bolt, Wavemaster
1/4-20 X 1-1/4" long mounting bolt that secures the pump to the floor of the equipment compartment Used on the Wavemaster 4000, Wavemaster 6000 and Wavemaster 7000 3 jet pumps -
Sku: 30413Mounting Bolt Washer, Wavemaster
Stainless steel washer used with the bolts that secure a pump to the pump stand and the pump stand to the floor of the equipment compartment 5/16" -
Sku: 72462-BYPPower Cord, After-Market, 1-Speed, 60″
This power cord is a 14/3 (60" long) with flag terminals on both ends The cord has three wires inside which are BLACK, WHITE, GREEN, and is used on the one-speed Jet Pumps -
Sku: 72461-BYPPower Cord, After-Market, 2-Speed, 60″
This power cord is a 14/4 (60" long) with flag terminals on both ends The cord has four wires inside which are BLACK, RED, WHITE, GREEN and is used on the two speed Jet Pumps -
Sku: ML-1OZ-BYPSilicone Grease, 1 oz. Tube
Silicone grease ideal for lubricating o-rings -
This after-market impeller is used on the after-market Wavemaster 9000 (ver 2), 9000 (ver 3) and Wavemaster 9200 jet pumps This 2 5 HP impeller screws onto the pump motor's threaded shaft with regular right-hand threads -
This after-market impeller is used on the after-market 2 0 HP Wavemaster jet pumps This impeller screws onto the pump motor's threaded shaft with regular right-hand threads -
This after-market impeller is used on the after-market Wavemaster 5000 and 6000 jet pumps This 1 5 HP impeller screws onto the pump motor's threaded shaft with regular right-hand threads -
Sku: 71409-EXP2E Wear Ring
This is the XP2E wear ring for the after-market impellers 71406-SW, 71405-SB and 71404-SY Please check the dots at the end of your impeller Item 71406-SW (Silver, White), item 71405-SB (Silver, Blue) and item 71404-SY (Silver, Yellow) -
Sku: 30224Starite Shaft Seal
Sta-rite shaft seal used on the 1HP and 2HP jet pumps that use a copper heat sink on Hot Spring spas Reference number: U109-93SS -
This heavy-duty fiberglass-reinforced polymer split nut comes in two pieces and is designed to replace compression fitting nuts (aka pump union nuts) that have broken due to vibration, age and finally over-tightening The two halves of this fitting are held ...read more -
This is the after-market 3/4" Replacement Shaft Seal for the Wavemaster 7000 version 2 and the Wavemaster 9000 -
Sku: 71030Shaft Seal, Wavemaster 7000 (version 2) and 9000
This item is obsolete and replaced by:
71030-BYPReplacement Shaft Seal for the Wavemaster 7000 version 2 and the Wavemaster 9000 See item 71030-BYP for after-market shaft seal -
Stainless steel screw used to secure the heater to the equipment compartment floor on Hot Spring & Tiger River spa models Also used on the SilentFlo 5000 Circulation pump and to hold the Ozonator to the wall of the equipment compartment -
Sku: 72349Rubber Feet, Wavemaster (Set of 4)
Rubber Mounts (feet) for the Wavemaster jet pump These are used to buffer the vibrations from the jet motor within the equipment compartment Comes in a set of four -
This replacement compression fitting split nut (AKA Split Union Nut-2") is used to connect heaters on the 1993-1994 Hot Spot Z, all 1998-current Hot Spot models, Solana models beginning in 2000 and all 1992-1994 Tiger River spas It is designed in two half ...read more -
Sku: 300349Rubber Foot, Wavemaster
Used on the base of the Wavemaster 8000 (ver 3), 8200, 9000 (ver 3) and 9200 jet pump to reduce the pumps noisy vibrations being transferred to the spa shell Sold individually -
This slinger is for the Wavemaster 7000 version 2 and the Wavemaster 9000 If the pump's shaft seal was to begin leaking, the slinger would "sling" water off the shaft to prevent that water from migrating into the electric motor -
Sku: 72344Exhaust Hose, Wavemaster
This exhaust hose connects onto the rear of the jet pumps shroud (if equipped) to discharge hot air from the jet pump motor This method of cooling the jet pump ensures a longer lifespan of the pump's motor -
Sku: 34470Jet Pump Ring Adapter 1-1/2in X 2in
This adapter converts the jet pump 1-1/2" inlet and outlet (suction & discharge) to 2" It has threads on the inside and outside and is used on various Hot Spring, Tiger River, and Hot Spot spa models This item is most often used on the Wavemaster 3000 ...read more -
Sku: 34495Jet Pump Ring Adapter O-ring
O-ring for the Jet Pump Ring Adapter that fits between the adapter nut and the jet pumps' suction & discharge -
The diffuser mounts onto the seal plate of the Wavemaster 7000 second version and the Wavemaster 9000 jet pump using seven stainless steel screws -
Volute for the Wavemaster 7000 version 2 and the Wavemaster 9000 v 1 -
Sku: 70945Gasket, Impeller Screw Wavemaster 9000
This little gasket fits over the impeller screw and is snugged into place against the impeller when the screw is tightened -
Impeller for the Wavemaster 9000 jet pump This 2 5 HP impeller screws onto the pump motor's threaded shaft with regular right-hand threads
Showing 61–90 of 131 results