Wet End Kit,0.75 hp, 48fr, Side Discharge, 1-1/2″ intake/discharge, Gecko Aquaflo FMHP series

Item #: 70331
$271.90

This is the “wet end” for the 0.75 HP FMHP series pump (side discharge). The intake and discharge measure 1-1/2″. This “wet end” will attach to your existing motor. Your jet pump is comprised of two main components: the electric motor and the “wet end”. In some cases, this entire “wet end kit” is needed. Perfect remedy if your “wet end” has cracked since neither the volute (attaches to the motor) or the volute cover (front of the pump) are available individually from the manufacturer.

  • Add Compression Fitting O-Rings?:

  • Add Bleedline Nipple Tiger River/Limelight? (33732):

View OEM
SKU: 70331 Categories: , Tags: , ,

Description

What’s Included: Volute, volute cover, volute o-ring, volute stainless steel screws, wear ring, impeller, and the shaft seal.

Description: This is the “wet end” for the 0.75HP, 48Frame, FMHP series pump (side discharge). The intake and discharge measure 1-1/2″. This “wet end” will attach to your existing motor. Your jet pump is comprised of two main components: the electric motor and the “wet end”. In some cases, this entire “wet end kit” is needed. Perfect remedy if your “wet end” has cracked since neither the volute (attaches to the motor) or the volute cover (front of the pump) are available individually from the manufacturer.

Installation: All “wet end kits” come pre-assembled from the factory. To install this kit you’ll disassemble it then re-assemble it one piece at a time onto your existing pump motor. Typical assembly time is two hours for the non-service tech. After connecting the pump unions (compression fittings) the pump may not align with the holes that anchor the pump to the floor of the equipment compartment. You may need to re-anchor using no longer than 1″ lag bolts. When pre-drilling for those bolts, do not pre-drill more than 1/4″ into the floor of the equipment compartment or you may drill into plumbing lines.

Wet end will work the following pump models:
02107000-1010
Wet End Impeller Shaft Seal Wear Ring
70331* 70332** 71447-BYP 70220

*Stamped on volute: 92770501A. Stamped on suction cover: 9123130.
**70332 Dots: Red (use 70220 wear ring)
If you can’t determine the dots on your impeller, buy the entire wet-end kit. The installation time is about the same.

View Diagrams & Part Compatibility

You may also like…

  • Shaft Seal Kit, Wavemaster
    The shaft seal kit is used to prevent water from leaking from around the rotating pump shaft This seal kit is used on most of the Wavemaster and after-market jet pumps Please find your pump model number and if your pump is an OEM Wavemaster, you will also ...read more
    $19.30
    Add to cart
  • Wavemaster Wear Ring
    The jet pump wear ring keeps water from back flowing around the impeller which would reduce the jet pressure significantly   It fits inside the "wet end" and slides over the impeller with the ridge side farthest away from the front of the impeller (i e , ...read more
    $7.28
    Add to cart
  • Impeller, 0.75 HP, Aquaflow FMHP/CP, #91693551
    Impeller for the 0 75HP Flow-Master/Circ-Master pumps For the entire wet end kit, see item 70331
    $29.51
    Add to cart
  • Jet Pump Ring Adapter 1-1/2in X 2in
    This adapter converts the jet pump 1-1/2" inlet and outlet (suction & discharge) to 2" It has threads on the inside and outside and is used on various Hot Spring, Tiger River, and Hot Spot spa models This item is most often used on the Wavemaster 3000 ...read more
    $10.52
    Add to cart