After-Market Wet End Kit, Wavemaster 8000 2.0 hp Pump

Item #: WE-34505
$119.20

This is the AFTER-MARKET “wet end” of the jet pump. Your Wavemaster 8000, 2.0 HP jet pump is comprised of two main components: the electric motor and the “wet end”. In some cases, this entire “wet end kit” is needed. Perfect remedy if your “wet end” has cracked since neither the volute (attaches to the motor) or the volute cover (front of the pump) are available individually from the manufacturer.

  • Add Compression Fitting O-Rings?:

  • Add Bleedline Nipple Hot Spring/Solana/Hot Spot? (32267):

  • Add Bleedline Nipple Tiger River/Limelight? (33732):

  • Add Slinger (71551)

SKU: WE-34505 Categories: , Tags: , ,

Description

What’s Included: Volute, volute cover, volute o-ring, volute stainless steel screws, wear ring, impeller, and the shaft seal.

Description: This is the AFTER-MARKET “wet end” for the Wavemaster® 8000, 2.0HP pump. The intake and discharge measure 1-1/2″. This “wet end” will attach to your existing motor. Your Wavemaster 8000  jet pump is comprised of two main components: the electric motor and the “wet end”. In some cases, this entire “wet end kit” is needed. Perfect remedy if your “wet end” has cracked since neither the volute (attaches to the motor) or the volute cover (front of the pump) are available individually from the manufacturer.

Installation: All “wet end kits” come pre-assembled from the factory. To install this kit you’ll disassemble it then re-assemble it one piece at a time onto your existing pump motor. Typical assembly time is two hours for the non-service tech. After connecting the pump unions (compression fittings) the pump may not align with the holes that anchor the pump to the floor of the equipment compartment. You may need to re-anchor using no longer than 1″ lag bolts. When pre-drilling for those bolts, do not pre-drill more than 1/4″ into the floor of the equipment compartment or you may drill into plumbing lines.

Wet end will work the following pump models:
34505; 02120000-1010
Wet End Impeller Shaft Seal Wear Ring
WE-34505* 70972** 71447-BYP 70220

*Label on the wet-end: 91040730-000
**70972 Dots: blue (use 70220 wear ring)
If you can’t determine the dots on your impeller, buy the entire wet-end kit. The installation time is about the same.

View compatibility table & diagrams

You may also like…

  • Wavemaster Wear Ring
    The jet pump wear ring keeps water from back flowing around the impeller which would reduce the jet pressure significantly   It fits inside the "wet end" and slides over the impeller with the ridge side farthest away from the front of the impeller (i e , ...read more
    $2.38
    Add to cart
  • Impeller, Wavemaster 8000
    This 2 0 HP impeller was used on the first version of the Wavemaster 8000 On the 1994, 1995 & 1996 Tiger River Khyber spa model This impeller screws onto the pump motor's threaded shaft with regular right-hand threads for
    $23.67
    Add to cart
  • Volute O-ring, Wavemaster
    Large o-ring that fits in between the two halves of the "wet end" (volute & volute cover) of the FMHP Series Wavemaster 3000, Wavemaster 5000 & Wavemaster 8000 jet pumps
    $2.05
    Add to cart
  • Shaft Seal Kit, Wavemaster
    The shaft seal kit is used to prevent water from leaking from around the rotating pump shaft This seal kit is used on most of the Wavemaster and after-market jet pumps Please find your pump model number and if your pump is an OEM Wavemaster, you will also ...read more
    $17.63
    Add to cart