After-Market Wet End Kit,1.0 hp, 48fr, Side Discharge, 2″ intake/discharge

Item #: WE-71894
$112.85

This is the AFTER-MARKET “wet end” for the 1.0HP pump. The intake and discharge measure 2″. This “wet end” will attach to your existing motor. Your jet pump is comprised of two main components: the electric motor and the “wet end”. In some cases, this entire “wet end kit” is needed. Perfect remedy if your “wet end” has cracked since neither the volute (attaches to the motor) or the volute cover (front of the pump) are available individually from the manufacturer.

This part can be found on many Hot Spot, Solana models from 1998 to 2022

View Diagrams & Part Compatibility

  • Add Bleedline Nipple Hot Spring/Solana/Hot Spot? (32267):

  • Add Compression Fitting O-Rings?:

  • Add Bleedline Nipple Tiger River/Limelight? (33732):

  • Add Slinger (71551)

SKU: WE-71894 Categories: , Tags: , ,

Description

What’s Included: Volute, volute cover, volute o-ring, volute stainless steel screws, wear ring, impeller, and the shaft seal.

Description: This is the AFTER-MARKET “wet end” for the 1.0HP, 48Frame pump (side discharge). The intake and discharge measure 2″. This “wet end” will attach to your existing motor. Your jet pump is comprised of two main components: the electric motor and the “wet end”. In some cases, this entire “wet end kit” is needed. Perfect remedy if your “wet end” has cracked since neither the volute (attaches to the motor) or the volute cover (front of the pump) are available individually from the manufacturer.

Installation: All “wet end kits” come pre-assembled from the factory. To install this kit you’ll disassemble it then re-assemble it one piece at a time onto your existing pump motor. Typical assembly time is two hours for the non-service tech. After connecting the pump unions (compression fittings) the pump may not align with the holes that anchor the pump to the floor of the equipment compartment. You may need to re-anchor using no longer than 1″ lag bolts. When pre-drilling for those bolts, do not pre-drill more than 1/4″ into the floor of the equipment compartment or you may drill into plumbing lines.

Wet end will work the following pump models:
71894, 06610006-2040, 37334, 39827 or 39575
Wet End Impeller Shaft Seal Wear Ring
WE-71894* 71695** 71447-BYP 71409

*Stamped on leg of wet end:92772705
**71695 Dots: orange (use 71409 wear ring)
If you can’t determine the dots on your impeller, buy the entire wet-end kit. The installation time is about the same.

View Diagrams & Part Compatibility

Ref. Diagram
# 16 XP2/LX Jet Pump, Wavemaster (Hot Spot 2019 - 2019) View Diagram
# 2 Jet Pump, Wavemaster XP2/LX (Solana 2003 - 2010) View Diagram
brand model years
Hot Spot Relay (REL) 2019
Hot Spot Rhythm (RHY) 2019
Hot Spot Stride (STD) 2019, 2020
Hot Spot SX (SX) 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018, 2019, 2020
Hot Spot TX (TX) 2022
Solana RX (RX) 2003, 2004, 2005, 2006, 2007, 2008, 2009
Solana X (Indoor Only) (X) 2000, 2001, 2002
Hot Spot Sorrento (SOR) 2003
Hot Spot Hotspot 2 (Y) 1998, 1999, 2000, 2001, 2002
Hot Spot RLX (ZQ) 1998, 1999, 2000, 2001, 2002
Solana RX (RX) 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010
Hot Spot TX (TX) 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018
Solana X (Indoor Only) (X) 2000, 2001, 2002
Hot Spot Dash (DAS) 2010, 2011, 2012
Hot Spot Mallorca (MAL) 2004, 2005, 2006, 2007, 2008, 2009
Hot Spot Mallorca (MALS) 2003, 2004, 2005, 2006, 2007, 2008, 2009
Hot Spot Pace (PAC) 2020
Hot Spot Relay (REL) 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018
Hot Spot Rhythm (RHY) 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018
Hot Spot Sorrento (SOR) 2003
Hot Spot Sorrento (SORS) 2003
Hot Spot Sprint (SPR) 2010, 2011
Hot Spot Trinidad (TRI) 2003, 2004, 2005, 2006, 2007, 2008, 2009
Hot Spot SLXtra (W) 2002
Hot Spot Hotspot 2 (Y) 1998, 1999, 2000, 2001, 2002
Hot Spot SLX (YQ) 1998, 1999, 2000, 2001, 2002
Hot Spot RLX (ZQ) 1998, 1999, 2000, 2001, 2002

You may also like…

  • Shaft Seal Kit, Wavemaster
    The shaft seal kit is used to prevent water from leaking from around the rotating pump shaft This seal kit is used on most of the Wavemaster and after-market jet pumps Please find your pump model number and if your pump is an OEM Wavemaster, you will also ...read more
    $19.30
    Add to cart
  • Impeller, Wavemaster 4000
    Replacement impeller for the Watkins Wavemaster 4000 jet pump This impeller screws onto the pump motor's threaded shaft with regular right-hand threads Please verify your pump's model number and vendor code when selecting replacement parts
    $43.23
    Add to cart
  • Wear Ring, Wavemaster
    The jet pump wear ring keeps water from back flowing around the impeller which would reduce the jet pressure significantly It fits inside the "wet end" and slides over the impeller with the ridge side farthest away from the front of the impeller (i e , ...read more
    $4.19
    Add to cart