I would like to express how excellent this company is. I inherited a house with a 2007 Hotspring Aria hot tub. The spa hasn’t been operated in years and when I turned it on, it ran for about 10 minutes and died. I mean dead died. I knew absolutely nothing about hot tubs but with the excellent diagnosis videos, installation videos and superior phone support, I was able to replace the main control board, heater relay board, heater, circulation pump, the ozonator and all associated tubing. This took 4 1/2 hours over two days (I had to watch videos) but the spa runs like new! I had one question regarding the jumper voltage 18 or 12. I spoke with a technician and he was able to answer my question as well as helping me double check the voltages for the components on the relay board. I am handy with electronics and electricity and am comfortable working with 230 volts. Shipping was fast and as expected. I highly recommend BackYardPlus.On 06/28/2024 by F. R. (verified customer)
All of our accessories are easy to install and make owning a great brand of hot tub even sweeter. Just when we think our Hot Spring spa can’t get any better, the engineers at Watkins dream up another cool idea and bring it to fruition. Explore some of the add-ons we enjoy in our spas.
Showing 1–30 of 83 results
-
Sku: 37876
Uprite Cover Lifter (7in Clearance)
The Uprite® Lifter is a favorite for close clearance needs If your spa needs to be nudged up close to the house, fence or gazebo then this lifter is ideal The Uprite® (sometimes spelled upright) only requires seven inches (7") of rear clearance to ...read more -
The CoverCradle® is our smoothest operator As the spa cover is folded back the “cradle” design is assisted by dual pneumatic gas shocks lowering it to a gentle rest It only needs twenty-four inches (24") of rear clearance
-
Sku: 72573
Side Arm Assembly, Cover Cradle
This black side arm is used on the CoverCradle and the CoverCradle II It attaches to the side of the spa cover and then to the side of the spa -
Sku: 71794
Gas Spring-Uprite
The Uprite® Cover Lifter employs two gas shocks that assist in opening the spa cover Sometimes these gas shocks can fall victim to the elements (storms, crazy uncles, frat parties etc ) and need replacing Replacement time is approximately thirty seconds ...read more -
There were two different sized ball studs used on Hot Spring cover lifters One is this 1/4" threaded shaft and the other (3rd qtr 2009) is 5/16" threaded shaft (part 75149) Either one size or the other will be on your cover lifter but not both sizes Ball ...read more
-
Sku: 72574
Hardware Bag #1, Cover Cradle
This Cover Cradle & Cover Cradle II hardware bag #1 includes the following: Four Hole Side Hinge (Qty 2) Four Hole Rear Hinge (Qty 2) #10 x 1" Flat Head Screws (Qty 8) #10 x 1-1/2" Flat Head Screws (Qty 8) Note: The items in this hardware bag are ...read more -
Sku: 71095
Gas Shock, Cover Cradle
Replacement 40lb gas spring shock for all models of the Cover Cradle cover lifter Gas shock color is black -
Sku: 76028-BYP
MetalTrap Clean Screen Pre-Filter, 10,000 Gallons (Approx. 20 Hot Tub Uses), For Pool or Spa
METALTRAP™ is a unique, patent-pending, water filtration technology designed to selectively filter out stain-causing metals found in water Unfiltered water can damage finishes and equipment and cause discoloration and odors METALTRAP™ is ...read more -
Sku: 75103
Gas Spring Lock-Uprite
The Gas Spring lock is used to secure the Uprite Lifter in the open position attaching to only one gas shock This part is typically left off when installing the Uprite Cover Lifter unless the spa is located in a windy area -
This ball stud is found on 3rd quarter 2009 and newer UpRite, Cover Cradle and Cover Cradle II lifters The older cover lifters used a 1/4" threaded shaft ball stud which is part# 71107-BYP
-
Sku: 71793
Angle Bracket-Uprite
Angle bracket for Uprite cover lifter -
This ozone receptacle was introduced in 1995 on the Hot Spring and Tiger River control boxes They were eliminated in the beginning of 1997, only to be added back in the early second quarter of 1997 This receptacle is no longer needed with the new style of ...read more
-
Sku: 72572
Crosslink Assembly, Cover Cradle
The Crosslink Assembly is the large "U" shaped bar that spans from the right side pivot assembly to the left side on the Cover Cradle and the Cover Cradle II cover lifter -
This part attaches onto the right side of the spa cover
-
Sku: 73451
Hardware Bag #1, Uprite Cover Lifter
Bag #1 for the upright cover lifter Contains the following: 2 x 1/4 x 20 5/8" Hex Bolts 2 x 1/4 x 1" Fender Washers 2 x 2 Hold Deck Hinge 10 x #10 Washers 8 x #10 1/2" Square Panhead Self Tapping Screws 10 x #10 1 1/2" Square Pan Tapping Screws 12 ...read more -
Right side bracket (as you are facing the spa folding the cover away from you) for the Uprite cover lifter
-
Sku: 71789
Upright Side Bracket Assembly, Left Side
Left side bracket (as you are facing the spa folding the cover away from you) of the Uprite cover lifter -
Sku: 75152
Upright Extension Tube
One pair (quantity of two) of extensions for the Uprite cover lifter -
Sku: 75150
Uprite Channel Pivot Assembly, Left Side
This part attaches onto the left side of the spa cover -
Sku: 72571
Cover Cradle Left Side Pivot Assembly
The left side pivot assembly viewed standing behind the Cover Cradle -
Sku: 72570
Cover Cradle Right Side Pivot Assembly
The right side pivot assembly viewed standing behind the Cover Cradle -
Sku: 74080
SpAudio II Sony Stereo Interface Cable
This cable allows the IQ2020 control box to communicate with the Sony Marine Stereo used in the Spaudio II Without this cable, the spas remote control or topside control cannot be used to operate the Sony Stereo -
Sku: 73928
SpAudio II Sony System
Sony replacement unit for the SpAudio II sound system -
Sku: 73731
SpAudio II Antena
This is the antenna used on the Spaudio II sound system This antenna allows for the radio to receive FM stations The antenna basically just lays down inside the equipment area but an extension can be added to place the antenna outside of the spa for ...read more -
Sku: 72853
SpAudio Hardware Bag
Hardware for Spaudio -
Sku: 71744
Washer, Gliderite
These washers are used with the ¼” – 20 x 5/8” Hex Head Bolts & ¼” – 20 x 1” Hex Head Bolt on the Gliderite and also used on the Uprite cover lifter -
Sku: 50049
Square Cover Lifter Bit
Square cover lifter bit -
Sku: 78164
Upright Lifter and Pro Lifter Spacer
This spacer is used on Upright cover lifters for HSS (Hot Springs Spas) and Pro Lifter Caldera For 2018 and newer Limelight models – spacer kit PN 78164 is required to install an UpRite lifter (PN 37876) to create space needed due to the small corner ...read more -
This version of the Cover Cradle I cover lifter is specifically designed for the 1998-2000 Hot Spring Classic only
-
Sku: 74043
SpAudio II Hardware
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com This is the hardware kit for adding extra inputs to the Spaudio II sound system
Showing 1–30 of 83 results