Thank you so much for helping me figure out my Vistabhot springs spa issue . The service call on the phone was fast, to the point and just excellent. Not only did Paul know what exact part I needed , he instructed me how to fix it ! and trouble shoot one more issue . This company is a great asset for the home owner that just needs a little extra help. Part delivery was on time and I saved tons of money on a service call . This is my go to place for any hot tub spa repairs ! Highly recommend to anyone and excellent nice service and nice people to talk to.,A+ and my wife’s happy !!On 05/21/2024 by J. S. (verified customer)
Showing 1–30 of 45 results
-
Sku: 300055
Spring Clamp, 3/4 inch
3/4" spring clamp (aka wire clamp) is used to secure the 3/4 inch vinyl tubing (70315) to various components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers or hose clamp pliers to ...read more -
Sku: 31134
Spring Clamp, 1/4in
Used to secure 1/4" (ID) vinyl tubing 70318 (OD measure 7/16") to various components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers or hose clamp pliers to squeeze, then slide this ...read more -
Sku: 31228
Spring Clamp, 1/2in
1/2" spring clamp for securing 1/2" ID vinyl tubing (70316) to components Item 70316 has an inner diameter of 1/2" and an outer diameter of 3/4" This clamp fits the 3/4" OD Note: Wear eye protection when squeezing these little rascals Service techs ...read more -
Sku: 30297
Nut, Volute Clamp, Starite
Used to tighten the volute clamp that binds the volute and seal plate together on all 1HP and 2HP Starite Max-E-Glas jet pumps that were used on some Hot Spring spa models prior to 1994 -
Sku: 34465
Spring Clamp, 3/8in
3/8" spring clamp (aka wire clamp) is used to secure the 3/8 inch vinyl tubing 70317 (9/16" OD) to various components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers are hose clamp ...read more -
Sku: 72574
Hardware Bag #1, Cover Cradle
This Cover Cradle & Cover Cradle II hardware bag #1 includes the following: Four Hole Side Hinge (Qty 2) Four Hole Rear Hinge (Qty 2) #10 x 1" Flat Head Screws (Qty 8) #10 x 1-1/2" Flat Head Screws (Qty 8) Note: The items in this hardware bag are ...read more -
Sku: 30396
Nut, #1/4in-20in Stainless Steel
Stainless steel nut used to secure the 220 volt Hot Spring heater elements (31409-BYP) to the heater housing (70192) -
Sku: 300602
Spring Clamp, 1in
1" spring clamp (wire clamp) used to secure 1" vinyl tubing -
Sku: 72714
Hardware Bag #2, Cover Cradle II
This Cover Cradle II hardware bag #2 includes the following: 1/4"-20 x 3/4" Stainless Steel Hex Bolts (Qty 4) #10 x 1-1/2" Stainless Steel Flat Head Screws (Qty 8) #10 x 1-1/2" Stainless Steel Pan Head Screws (Qty 14) Note: The items in this hardware ...read more -
Sku: 30105
Romex Clamp 3/4in
This clamp is used as strain relief is used to secure the heater's power cord to the bottom of the IQ Control box The strain relief prevents the cord from accidentally being disconnected from inside the control box should the cord be pulled down -
Sku: 73451
Hardware Bag #1, Uprite Cover Lifter
Bag #1 for the upright cover lifter Contains the following: 2 x 1/4 x 20 5/8" Hex Bolts 2 x 1/4 x 1" Fender Washers 2 x 2 Hold Deck Hinge 10 x #10 Washers 8 x #10 1/2" Square Panhead Self Tapping Screws 10 x #10 1 1/2" Square Pan Tapping Screws 12 ...read more -
Sku: 72715
Hardware Bag #3, Cover Cradle II
This Cover Cradle II hardware bag #3 is only for spas with removable exterior panels and includes the following: #10 x 2" Stainless Steel Flat Head Screws (Qty 8) #10 x 2" Stainless Steel Pan Head Screws (Qty 14) Note: The items in this hardware bag are ...read more -
Sku: 37752
Wing Nut,10-24 Stainless Steel
This wing nut is used to hold the bulb clamp in place on the heater body in Tiger River spas from 1992 to 1994 The bulb clamp holds the copper thermostat and hi-limit bulbs to the side of the heater where they are used to monitor the temperature of the spa ...read more -
Sku: 33253
Nut, Speed Narrow
Nut, speed narrow -
Sku: 32736
Nut, Lock 1/4in (Thin)
1/4in lock nut -
Sku: 300859
Nut, 2.5mm
This nut is used to secure the circuit board to the back of the control panel bezel on Tiger River spas from 1992-1997 It replaces a small spring clamp that used to do the same job The posts that the nut screws on to are actually plastic and are not ...read more -
Sku: 34029
Nut 10-24 Nylon
Nut 10-24 Nyloc -
This nut goes onto the volute bolt that secures the seal place to the volute
-
Sku: 75105
Hardware Bag #4 for Upright Cover Lifter
Hardware for the upright spa cover lifter -
Obsolete: Factory replacement suggestion item #72714 Hardware Bag #2 used on the Cover Cradle and Cover Cradle II It contains screws for mounting the cover lifter to the spa and cover All screws use Robertson (square drive) head bits
-
Sku: 30393
Nut, Brass – Cap #1/4in-20
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Nut, Brass - Cap #1/4in-20 -
Sku: 30390
Nut, Hex #10-24in
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Nut, Hex #10-24in -
Sku: 30394
Nut, #10-24 X 3/4in Plt Coupling
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Nut, #10-24 X 3/4in Plt Coupling -
Sku: 30395
Nut, Coupling #1/4in-20 X 7/8in
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Nut, Coupling #1/4in-20 X 7/8in -
Sku: 73166
Hardware Bag, Lift ‘N Glide
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Twenty stainless steel screws, 1 1/2" long used to attached the Lift 'N Glide cover lifter to the spa -
Sku: 71220
Nut, Slot 1/4in
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com -
Obsolete: Factory replacement suggestion item 75149 This kit (item#7 in the diagram) includes the following parts for the Cover Cradle: 1/4" Ball Stud X 4 1/4" Split Lock Washer X 2 1/4" Slot Nuts X 2 1/4" Nut
-
Sku: 73163
Clarion Hardware Bag
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com This hardware bag contains all of the hardware necessary to mount five Clarion Light Bars It does not ...read more -
Sku: 71564
Nut, Hex 1/4in X #20 99560050
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Hex nut, 1/4in x #20 -
Sku: 34487
Snap Clamp Snp #6
OBSOLETE: Use 31134 This is a #6 size snap clamp used on 1/4" vinyl tubing Snap Clamp (Min Dia In ) 0 449 / (Max Dia In ) 0 511
Showing 1–30 of 45 results