On 04/15/2024 by R. D. (verified customer)
Brand: Hot Spring, Hot Spring Pre 89, Lift N Glide
Showing 61–90 of 200 results
-
Sku: 72775-x1-BYPIntake Vent Screen
This aluminum perforated strip mounts at the bottom of the equipment access door to keep rodents from making their home in the warmth of your Hot Spring or Tiger River spas equipment compartment This screen is cut to length Not available for the Hot Spring ...read more -
Sku: 30344Screw, #8 X 1in Stainless Steel
Stainless steel screw, #8 x 1in, used on the air control lever of Hot SPring models from 1989-1993 -
Sku: 30098Strain Relief, Control Box, 3/8in
This strain relief is used to secure the circ pump and Ozonator's power cord to the bottom of the IQ Control boxes The strain relief prevents the cord from accidentally being disconnected from inside the control box should the cord be pulled down -
Sku: 36044Plug, Hole, 0.50
This plug is used to fill openings found on the back of the IQ2000 and IQ2020 Control box that can be used to allow wiring to enter the control box These plugs cover the openings that are not in use to help prevent dust, dirt, and insects from entering the ...read more -
Sku: 30261O-Ring, Union, Starite
O-ring for the compression fitting union used on the 30215 Starite Jet Pump -
Sku: 36586Clip, Extruded Air Valve
Used to hold the air intake for the Freshwater II Ozonator in place on the wall in the equipment compartment near the Ozonator Found in Hotspring and Tiger River Spas with Freshwater II Ozonators -
Sku: 36022Strain Relief 10/3
Heater strain relief used to secure the heaters power cord to the bottom of the IQ Control boxes The strain relief prevents the cord from accidentally being disconnected from inside the control box should the cord be pulled down -
Sku: 1299901Niche Nipple Repair Plug
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Used on models prior to 4th quarter 2012 To install the niche repair plug (stint), use the tool, ...read more -
Sku: 73271Hydrostream Jet O-Ring
This o-ring is used in the Hydrostream jet for Hotsprings spas made from 2004-2011 It is seated between the jet body and the back side of the shell of the spa and makes the seal between the jet and the spa shell -
Impeller screw for the Wavemaster 7000 (v 1) This screw is reversed thread (left hand thread) This screw is not needed if you are purchasing a new impeller 2014 forward -
Sku: 37262Mounting Screw, Control Panel
Two of these screws are used to hold the control panel assembly to the spa These screws are hidden by the frosted light cover that is found at the top of the control panel bezel -
Sku: 34017Equipment Door Fastener, Male Piece
This pointed fastener attaches onto the equipment compartment access door and is inserted into its counter-part fastener that is attached to the door frame of the equipment compartment -
Sku: 36043Control Box Plug, for 0.875 Hole
Black plastic plug used on the IQ 2000 and IQ 2020 Control Boxes to seal off an unused port helping to prevent bugs, dirt and debris from making a home inside the control box -
Sku: 35986O-Ring, Adj/Jet Small, Hot Spring
Small o-ring used on various jets -
Wall fitting nut o-ring -
Sku: 30100Strain Relief Bushing, 1/2in
This bushing is used for strain relief of cords that are 1/2" in diameter, such as the cord for the heater in a Hotsprings, Tiger River, or LimeLight spa -
Sku: 76549Fibercore Replacement Kit
This Fibercor Replacement Kit can be used on all Hot Spring Spa models from 2007 to 2018 and all 2019 Limelight and Hot Spot Spa models This Kit contains approximately 8 pounds of material, which is about 4 cubic feet -
Sku: 72714Hardware Bag #2, Cover Cradle II
This Cover Cradle II hardware bag #2 includes the following: 1/4"-20 x 3/4" Stainless Steel Hex Bolts (Qty 4) #10 x 1-1/2" Stainless Steel Flat Head Screws (Qty 8) #10 x 1-1/2" Stainless Steel Pan Head Screws (Qty 14) Note: The items in this hardware ...read more -
Sku: 70945Gasket, Impeller Screw Wavemaster 9000
This little gasket fits over the impeller screw and is snugged into place against the impeller when the screw is tightened -
Same urethane foam used at the factory This kit is used primarily to adhere to the pieces of foam insulation that were removed to repair a leak, saving the pieces of foam and placing them back into the foam void using this kit to fossilize the foam pieces ...read more$169.04 Select Options -
Four of these stainless steel screws are used to mount the control head (the electronic part of the control panel) to the control panel bezel These are accessible from behind the control head -
Sku: 73249Panel Clips, Male and Female, QTY 4
Panel clips, male/female, for the removable panels on Hot Spring models, quantity of 4 -
Sku: 30407Washer, Nylon Flt (Thin)
Nylon washer for the jet selector water diver valve on all Hot Spring & Tiger River spa models manufactured prior to 1994 -
Sku: 20120Control Box Power Cord, Heavy Duty 20amp
This extreme weather, heavy-duty 20amp 120volt power cord is used with the 20amp GFCI on 120volt Hot Spring, Tiger River, Solana, and Hot Spot spa models -
Sku: 10057Jet Spanner Wrench
Service Tool: This spanner wrench is designed to expand to the desired width and insert into the indentations on the outside ring of various jet wall fittings -
This stainless steel impeller screw (left-hand threads) screws onto the end of the motor shaft to secure the impeller from spinning off of the Sta-rite Maxi-Glass 1hp & 2hp pumps that were used in Hot Spring spas prior to 1994 -
Sku: 34363Screw,#10-32 X 1-1/2in
This gray-colored tipped 1-1/2" long screw secures the control panel in place on all 1994-1997 wood-sided Hot Spring models and is also found in various other locations such as the Dream Pillow etc -
Sku: 30118Cordgrip, Thermostat
This cord grip fitting is what seals around the 30203 and the 75077 control thermostats copper wire May require the 30690 adapter (not included) -
Sku: 70191Screw, Drain Slide 1-1/4in
Drain slide screw, 1-1/4" -
Sku: 34016Door Frame Fastener, Female
This fastener screws onto the top of the equipment compartment door frame and serves as an alignment for the male fastener
Showing 61–90 of 200 results