I would like to express how excellent this company is. I inherited a house with a 2007 Hotspring Aria hot tub. The spa hasn’t been operated in years and when I turned it on, it ran for about 10 minutes and died. I mean dead died. I knew absolutely nothing about hot tubs but with the excellent diagnosis videos, installation videos and superior phone support, I was able to replace the main control board, heater relay board, heater, circulation pump, the ozonator and all associated tubing. This took 4 1/2 hours over two days (I had to watch videos) but the spa runs like new! I had one question regarding the jumper voltage 18 or 12. I spoke with a technician and he was able to answer my question as well as helping me double check the voltages for the components on the relay board. I am handy with electronics and electricity and am comfortable working with 230 volts. Shipping was fast and as expected. I highly recommend BackYardPlus.On 06/28/2024 by F. R. (verified customer)
Find all the plumbing parts you need here. Flexi PVC tubing, Vinyl Tubing, Elbows, Tees, Diverter Valves, Levers & Bezels, Check-Valves, Couplers, and more.
Showing 1–30 of 58 results
-
Sku: 1044101-72228-AM-BYP
Tubing Kit, Del-Ozone-1/4in with Check valve
This 1/4" ID (3/8" OD) ozone-resistant tubing works with UO3 ozone generator It includes an attached 1/4" ozone-resistant check valve, clamps, mounting screws, and new flag terminals This assembly is approx five feet in length Note: There is a small ...read more -
Sku: 1044101-72228-BYP
Tubing Kit, Freshwater III Ozonator-1/4in Tygon/Kynar with Check valve
This 1/4" ID (3/8" OD) Kynar/Tygon ozone-resistant tubing kit comes standard with the Freshwater III Ozonators It is the replacement for all Freshwater 3 ozonators It includes an attached 1/4" ozone-resistant check valve This assembly is approx six feet ...read more -
Sku: 35233
Water Check Valve, 3/4 inch
This 3/4" water check valve is installed in the inlet side of the circulation pumps plumbing to prevent the backflow of water through the circulation pump once the jet pump is activated All water check valves have arrows stamped on the outside to indicate ...read more -
Air check valve for Hot Spring, Tiger River, and Hot Spot spa models This check valve is located in the equipment compartment under the bartop Its primary function is to prevent water from back flowing into the equipment compartment should a hydrotherapy ...read more
-
Sku: 30700
Cap, Drain Valve – 3/4in with Washer
Black 3/4" hose bib thread cap used on the drains of 1993 forward Hot Spring, Tiger River, Hot Spot, and Solana, and Limelight spa models It also includes the washer This cap is used both on the "Primary" Drain Valve, and the "Secondary" Drain Valve -
Sku: 38390
Check Valve, Air, with Ball 1/2in
It is used to prevent water from backing into the airlines when the jets are off It is at the back of the Moto-Massage housing and glued into a 90-degree elbow It is also on the jetstream jets -
Sku: 1044101
Check Valve (Ozone) Freshwater Ozone, 1/4in O.D.
Over time an Ozonator check valve will breakdown under the harsh conditions of ozone Our OEM check valves have a special diaphragm (Viton) that enables them to last longer than rubber Rubber diaphragms last about a month before the rubber becomes hard -
This heavy-duty fiberglass-reinforced polymer split nut comes in two pieces and is designed to replace compression fitting nuts (aka pump union nuts) that have broken due to vibration, age and finally over-tightening The two halves of this fitting are held ...read more
-
This yellow and black drain valve is found on Hot Spring, Tiger River, Hot Spot, and Solana spa models Simply connect your garden hose to the threaded end and turn the black knob and Viola!
-
Sku: 33833
Cap, Air Control/Jet Selector, White
This white cap fits on the top of the 1993-2003 Hot Spring Comfort Control air lever to identify it as the Comfort Control Lever for the Moto-Massage Jet on white-colored Hot Spring models only Note: Also used as an upgrade for the colored dots (sticker) ...read more -
This air check valve is located in the equipment compartment, up high, under the bar top If a hydrotherapy jet should become obstructed (like when a guest sticks their finger in the jet), this item becomes critical in preventing water from back flowing into ...read more
-
Sku: 72701
Hartford Loop Assembly
This retrofit kit is used to replace the air check valve that was used in some Hot Spring spa models This kit replaces the obsolete 72342 Check your serial number in the parts finder above to be sure this part is for your spa -
This "Jet System" check valve is used on all Hot Spring models and all Tiger River spas This check valve engages when the diverter valve is changed to different positions For convenience, the inside diameter of this check valve is 1-1/2" and the outside ...read more
-
Sku: 36225
Cap, Lever/Bezel, Quarite Teal
Lever cap in teal -
Sku: 72072-1.5
Split Nut for 1.5in Compression Fittings
This 1-1/2" split nut comes in two pieces and is designed to replace compression fitting nuts (aka pump union nuts) that have broken due to vibration, age, and over-tightening The two halves of this fitting are held together by two screws -
Sku: 73297
Cap, Drain Valve Assembly
Drain valve black cap, washer and ring assembly used on 2004 forward Hot Spring and Tiger River spa models -
Sku: 71981
Check Valve, with Spring, 1-1/2in
1-1/2" spring style check valve is commonly found between the jet pump and filter housing on Tiger River spas This check valve automatically closes when the Tiger River spas jet pump is turned off so the circulation pump (Silentflo 5000) can then draw water ...read more -
Drain Valve used on most 2004 and some 2005 Tiger River and Hot Spring spas It is opened by twisting the hose bib counter-clockwise and pulling the bib forward, and then removing the protective cap The cap also served as a way to grip the big Closed by ...read more
-
Reducer Bushing, 3/4" Spig x 1/2" Slip This bushing allows a 1/2" male slip fitting or 1/2" PVC pipe, rigid or flexible, to be adapted to fit in a 3/4" female slip fitting The connection should be made using PVC primer and cement
-
Sku: 30681
Bushing, 1-1/2in X 1in Sp X Slip
This bushing is used to adapt a 1" male PVC slip fitting to fit in a 1 1/2" female slip fitting, or to allow a 1 1/2" female slip fitting to accept a 1" male slip fitting -
Sku: 70326
Air Check Valve, Hot Spring Grandee
This one-way check valve was used in the Hot Spring Grandee from 1989-1993 for the Jet Stream Jet air intake All jets in a Hot Spring have both an air and water mixture If someone put their finger in a jet nozzle and restricted the water flow, water could ...read more -
Sku: 70327
Check Valve, Air, Hot Spring Classic
Air check-valve used the 1991-1993 Classic spa only for the JetStream Jet For the '89-'93 Grandee see part 70326 -
Sku: 31288
Reducer, 2in X 1-1/2in Spig X Slip
Reducer Bushing, 2" Spig x 1-1/2" Slip This bushing allows for a 1 1/2" male slip fitting or PVC pipe, rigid or flexible, to connect to a 2" female slip fitting The connection should be made using PVC primer and cement -
Reducing Bushing, 1"Spig X 1/2" Slip This bushing allows a 1/2" male slip fitting or 1/2" PVC pipe, rigid or flexible, to be adapted to fit in a 1" female slip fitting The connection should be made using PVC primer and cement
-
Sku: 70173
Check Valve (Water) 1/2in
This 1/2" water check valve is used on the discharge side of the old Laing circ pumps in pre-1990 Hot Spring 115volt Sovereign, Classic, Prodigy & Jetsetter models This is for 1/2" plumbing If your plumbing is 3/4" then use part 35233 -
Sku: 31420
Bushing, 1-1/2in X 3/4in Slip X Slip
This bushing accepts a 3/4" male PVC slip fitting or 3/4" PVC pipe, rigid or flexible, and will connect to a 1 1/2" female PVC slip fitting -
Sku: 30680
Bushing, 1-1/2in X 3/4in Sp X Slip
This bushing accepts a 3/4" male PVC slip fitting and will fit into a 1 1/2" female PVC slip fitting PVC primer and cement should be used to adhere this fitting -
Reducer Bushing, 1" Spig x 3/4" Slip This bushing allows a 3/4" male slip fitting or 3/4" PVC pipe, rigid or flexible, to be adapted to fit in a 1" female slip fitting The connection should be made using PVC primer and cement
-
Sku: 30667
Coupling, Reducer 1in X 3/4in Sxs
This adapter is used to join a 3/4" PVC male fitting and a 1" PVC male fitting together PVC primer and cement should be used to adhere the fittings -
Sku: 75010
Inlet Assembly with Check Valve
The four pieces of this pump inlet assembly come pre-assembled and include the check valve This assembly was used on the jet pump on the 1989 Hot Spring Jetsetter, Prodigy, and Sovereign Also used on the 1991-1992 Grandee
Showing 1–30 of 58 results