Best place ever, always goodOn 05/31/2024 by M. D. (verified customer)
Find all the plumbing parts you need here. Flexi PVC tubing, Vinyl Tubing, Elbows, Tees, Diverter Valves, Levers & Bezels, Check-Valves, Couplers, and more.
Showing 1–30 of 40 results
-
Sku: 34350
Diverter Valve Snap Ring
This snap ring is used on most of the diverter valves on Hot Spring & Tiger River spas A special snap ring tool is needed to remove this part -
Sku: 30237-x2-BYP
Compression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 301488
Sweep Pump Union, 2in Soc. 90 Degree
Two-inch SOC 90deg sweep pump union -
Sku: 1119401
Pump Union, 45 Degree
Pump union (aka compression fitting) can be used to connect to any Wavemaster pump later than 1996 This union accepts a 2" PVC pipe and will attach to a 2" standard pump thread The fitting for the pipe is at a 45-degree angle -
Sku: 73920
Water Feature On-Off Valve Assembly
This on-off valve assembly is found on Hot Spot and Limelight spa models from 2006 through 2014 It is used to turn on and off the bar top Amur water feature that runs off one of the jet pumps in the spa This valve turns 270 degrees, for 2014 tubs, please ...read more -
Sku: 73356
On/Off Valve Insert
This insert is used on the on/off valve for the soothing stream fountain used on certain Hotsprings spas between 2003-2009 This valve should be replaced if the fountain will not turn off completely when the valve is closed -
Sku: 73351
On/Off Valve .75
This on/off valve is used on Hotsprings spas to turn on and off the Soothing Stream water feature, which runs off the 24-hour circulation pump If the valve fails to shut off the water supply, remove the black internal section from the valve body, and ...read more -
This Coastal Gray On/Off Valve is used for the water feature on Hot Spot and Limelight tubs This valve turns 90 degrees, for 2014 tubs, please verify how far your existing valve turns If it turns 90 degrees, this is the correct replacement If your existing ...read more
-
Sku: 73350
On/Off Valve, Water Feature, 1.5in
This valve is used to turn on and off the Bella Fontana Water Feature in Hotspring Spas and the Amur Water Feature in Tiger River Spas -
Sku: 73327
On/Off Valve Handle Warm Gray
This warm grey handle was used on all water feature valves on Hotsprings and Tiger River spas from 2003 to 2009 that used warm grey jets and handles -
Reducer Bushing, 3/4" Spig x 1/2" Slip This bushing allows a 1/2" male slip fitting or 1/2" PVC pipe, rigid or flexible, to be adapted to fit in a 3/4" female slip fitting The connection should be made using PVC primer and cement
-
Sku: 73482
On and Off Valve, .75
This valve is used for the fountains on certain 2004 only Hot Springs spas The handle and body supplied are not used You should use the body that is mounted in the spa, and the bezel and handle that came with the spa as well -
Sku: 30681
Bushing, 1-1/2in X 1in Sp X Slip
This bushing is used to adapt a 1" male PVC slip fitting to fit in a 1 1/2" female slip fitting, or to allow a 1 1/2" female slip fitting to accept a 1" male slip fitting -
Reducing Bushing, 1"Spig X 1/2" Slip This bushing allows a 1/2" male slip fitting or 1/2" PVC pipe, rigid or flexible, to be adapted to fit in a 1" female slip fitting The connection should be made using PVC primer and cement
-
Sku: 70906
Elbow/Union Assembly, Hot Spot
This assembly is used in two places on the 1993-1994 Hot Spot equipment compartment One of these assemblies connects onto the discharge (top) of the Wavemaster 3000 jet pump and the other end connects onto one side of the heater The second place is on the ...read more -
Sku: 31420
Bushing, 1-1/2in X 3/4in Slip X Slip
This bushing accepts a 3/4" male PVC slip fitting or 3/4" PVC pipe, rigid or flexible, and will connect to a 1 1/2" female PVC slip fitting -
Sku: 30680
Bushing, 1-1/2in X 3/4in Sp X Slip
This bushing accepts a 3/4" male PVC slip fitting and will fit into a 1 1/2" female PVC slip fitting PVC primer and cement should be used to adhere this fitting -
Reducer Bushing, 1" Spig x 3/4" Slip This bushing allows a 3/4" male slip fitting or 3/4" PVC pipe, rigid or flexible, to be adapted to fit in a 1" female slip fitting The connection should be made using PVC primer and cement
-
Sku: 30685
Bushing, 2in X 1in Spig X Slip
This bushing accepts a 1" male PVC slip fitting and will fit into a 2" female PVC slip fitting PVC primer and cement should be used to adhere to this fitting -
Sku: 37681
Red Bushing, 2in X 3/4in (437-248)
Reducer Bushing, 2" Spig x 3/4" Slip This bushing allows a 3/4" male slip fitting or 3/4" PVC pipe, rigid or flexible, to be adapted to fit in a 2" female slip fitting The connection should be made using PVC primer and cement -
Sku: 78154
On and Off Valve, 90 Degree
90 degree on and off valve, for Limelight and Hot Spot models -
Sku: 70825-BYP
Snap Ring Pliers Tool, Smart Jet Diverter Valve
These snap ring ("c"-ring) pliers can be used to remove the snap ring on Smart Jet diverter valves (71494, 71495, 73768, 73769) found in most hot tubs Made of carbon steel and vinyl grip handles and comes with interchangable straight, 45 degree and 90 degree ...read more -
Sku: 74135
Bleedline Bushing, Hot Spring
Bleedline Bushing for 2001 Hot Spring Landmark Dream Jet Massage Plumbing System Fits between the spa shell and the bleedline fitting, part number 30598 The bleedline fitting supplies a small stream of water behind the pillow to prevent water from ...read more -
Sku: 31485
Bushing, 1-1/4in X 1in
This bushing accepts a 1" pipe or male PVC fitting and will fit into a 1 1/4" female PVC fitting PVC primer and cement should be used to adhere the fittings together -
This bushing accepts a 1/2" male pipe thread fitting and will connect to a 2" female PVC slip fitting PVC primer and cement should be used for the slip fitting side of this bushing Plumbers tape should be used on the 1/2" male pipe thread before it is ...read more
-
Reducer Bushing 1-1/2" Spig x 3/4 female iron pipe thread This bushing allows a 3/4" male pipe threaded fitting to be adapted to fit in a 1 1/2" female slip fitting The connection should be made using PVC primer and cement on the slip portion of the ...read more
-
This bushing adapts a 1/2" male PVC slip fitting to a 1/4" spig fitting PVC primer and cement should be used on the slip fitting
-
This bushing accepts a 1/2" male PVC slip fitting and will fit into a 2" female PVC slip fitting PVC primer and cement should be used to adhere this fitting
-
Reducer Bushing, 1-1/2" Spig x 1-1/4" Slip This bushing reduces a 1 1/2" female slip fitting down to a 1 1/4" female slip fitting PVC primer and cement should be used to glue the bushing in place
Showing 1–30 of 40 results