It was very easy to select the corret parts for my "serial Number". All parts were correct and operated as required.On 06/20/2024 by M. R. (verified customer)
Brand: Autofresh System, Hot Spring, Limelight, Starite, Tiger River
Showing 1–30 of 273 results
-
Sku: 74078Injector, Freshwater Ozone, Black
The injector fits in-line after the Silentflo 5000 (discharge side and after the heater) This Kynar plastic "venturi" injector is ozone resistant and is used with the Freshwater III High Output Ozonator by Watkins manufacturing, item 72602 -
Sku: 30598Bleedline Nipple, 1/4in, Hot Spring
This nipple is glued into various PVC fittings in various places on Hot Spring, Tiger River, Limelight, Hot Spot and Solana spa models Simply drill out the broken 1/4" barbed fitting with a 19/64" drill bit (only this size drill bit) Then glue this ...read more -
Sku: 34319Diverter Valve Collar O-Ring
This o-ring (some models have silicone adhesive) fits between the diverter valve collar and the spa shell to prevent water from dripping down into the equipment compartment This o-ring doesn't fit on the actual valve like the 34318 -
Sku: 30700Cap, Drain Valve – 3/4in with Washer
Black 3/4" hose bib thread cap used on the drains of 1993 forward Hot Spring, Tiger River, Hot Spot, and Solana, and Limelight spa models It also includes the washer This cap is used both on the "Primary" Drain Valve, and the "Secondary" Drain Valve -
Sku: 30482O-Ring, Wallfitting Front-Red
Silicone wall fitting o-ring used in various places on Hot Spring, Tiger River, Hot Spot, and Solana spas -
Sku: 36159Precision Jet Elbow
This elbow is used to glue onto the rear of the Precision Jet Body This elbow is an odd size and is not available at the local hardware store -
Sku: 34447-x2-BYPCompression Fitting O-rings, for 2 inch Union (Qty of 2)
(Quantity of 2 o-rings) O-rings used on the pumps 2" compression fittings ( 71036 ) found on most Hot Spring, Tiger River, Limelight, Hot Spot and Solana spa models Also used on the replacement "Wet End" pump kits and some heaters The 2" measurement refers ...read more -
O-ring used on the 2" compression fittings (71036) on most Hot Spring, Tiger River, Hot Spot, and Solana spa models The 2" measurement refers to the inner diameter of the most narrow part of the compression fitting/union The o-ring that is included measures ...read more -
Sku: 71036Compression Fitting, 2in with O-Ring
This 2" compression fitting, which includes the o ring, is sometimes referred to as a pump union or compression coupling It is found on the suction side of most Wavemaster® XP2 or XP2e Series Jet Pumps Other compression fittings are the 71038 and 71037 ...read more -
Sku: 30237-x2-BYPCompression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 71038Compression Fitting, 1-1/2in with O-Ring
This 1-1/2" compression fitting, which includes the o ring, is sometimes referred to as a pump union or compression coupling It is found on the suction and/or discharge side of FMHP/CP Series Wavemaster® Jet Pumps 2" x 1-1/2" Compression Fitting click ...read more -
This 2" compression fitting, which includes the o ring, is sometimes referred to as a pump union or compression coupling 1-1/2" Compression Fitting 2" Compression Fitting -
Sku: 301488Sweep Pump Union, 2in Soc. 90 Degree
Two-inch SOC 90deg sweep pump union -
Sku: 1119401Pump Union, 45 Degree
Pump union (aka compression fitting) can be used to connect to any Wavemaster pump later than 1996 This union accepts a 2" PVC pipe and will attach to a 2" standard pump thread The fitting for the pipe is at a 45-degree angle -
Sku: ML-1OZ-BYPSilicone Grease, 1 oz. Tube
Silicone grease ideal for lubricating o-rings -
This heavy-duty fiberglass-reinforced polymer split nut comes in two pieces and is designed to replace compression fitting nuts (aka pump union nuts) that have broken due to vibration, age and finally over-tightening The two halves of this fitting are held ...read more -
Sku: 36160Precision Jet Tee
This tee is used to glue onto the rear of the Precision Jet Body and provides a 1/2" connection on either side of the tee This tee is not available at the local hardware store -
Sku: 70382Coupling, Barbed, 1/4in x 1/4in
Barbed coupling used to splice together 1/4" vinyl tubing -
This plug has been used on the 220volt pre-1995 Hot Spring heater to cap off the drain hose by clamping the 1/4" vinyl drain tubing to the closed 1/4" nipple on this plug Also used in the 71557-BYP Kit -
Sku: 31417Adapter, 3/4in Barbed X 3/4in Slip
This barbed fitting is primarily used to connect 3/4" vinyl tubing to various places within the circulating/heating system of Hot Spring & Tiger River from 1990 forward This PVC fitting is often found glued into a 90-degree elbow rising from the floor of ...read more -
Sku: 73920Water Feature On-Off Valve Assembly
This on-off valve assembly is found on Hot Spot and Limelight spa models from 2006 through 2014 It is used to turn on and off the bar top Amur water feature that runs off one of the jet pumps in the spa This valve turns 270 degrees, for 2014 tubs, please ...read more -
Sku: 34473O-ring, Small, Diverter Valve
Small 0-ring for all 1994 to now Smart Jet Selector Valves (i e diverter valves) -
This yellow and black drain valve is found on Hot Spring, Tiger River, Hot Spot, and Solana spa models Simply connect your garden hose to the threaded end and turn the black knob and Viola! -
Sku: 34504Adapter, 3/4in Sp X 1/4in Sp
This adapter glues into a 3/4" female PVC slip fitting using PVC primer and cement and accepts a 1/4" vinyl hose that can be secured using PVC cement as well or a hose clamp -
This coupling is most often found on the discharge side of the Laing 303 and Calvert (Cal-200) circulating pumps The 3/4" x 3/4" x 1/4" bleed line fitting has a 1/4" nipple (30598) for the 1/4" vinyl tubing that's coming from the front of the jet pump to ...read more -
Flexible PVC is a ribbed looking white or beige type of PVC It comes in three-foot sections and is glued using PVC primer and PVC cement found at your local hardware store The diameter is measured from the inside (I D ) of the piping Note: This is ...read more -
Sku: 70308Flexible PVC, 2in inside Diamter X 3ft
Flexible PVC is a ribbed looking white or beige type of PVC This size is usually found coming off of the jet pump or water diverter valves (Smart Jet) It comes in three-foot sections and is glued using PVC primer and PVC cement found at your local hardware ...read more -
BACKORDERED WITH THE FACTORY - NO CURRENT ETA This perforated screen (grill) has many small holes to prevent debris from clogging the floor drain This screen simply unscrews from the 1-1/2" threaded floor fitting -
Sku: 77427Bleedline Fitting, Circulation Pump
Circulation Pump Bleedline Fitting This special Tee fitting includes 2 X 3/4" barbed fittings, as well as a 1/4" connection No PVC Glue needed and no assembly required like the 72727-BYP (Elbow, 3/4in X 3/4in Barbed with 1/4in Barbed Nipple)
Showing 1–30 of 273 results