It was very easy to select the corret parts for my "serial Number". All parts were correct and operated as required.On 06/20/2024 by M. R. (verified customer)
Plumbing: Barbed Adapter, Cap, Compression Fitting, Nipple, Restrictor, Snap Ring
Showing 1–30 of 43 results
-
Sku: 30700Cap, Drain Valve – 3/4in with Washer
Black 3/4" hose bib thread cap used on the drains of 1993 forward Hot Spring, Tiger River, Hot Spot, and Solana, and Limelight spa models It also includes the washer This cap is used both on the "Primary" Drain Valve, and the "Secondary" Drain Valve -
Sku: 34447-x2-BYPCompression Fitting O-rings, for 2 inch Union (Qty of 2)
(Quantity of 2 o-rings) O-rings used on the pumps 2" compression fittings ( 71036 ) found on most Hot Spring, Tiger River, Limelight, Hot Spot and Solana spa models Also used on the replacement "Wet End" pump kits and some heaters The 2" measurement refers ...read more -
O-ring used on the 2" compression fittings (71036) on most Hot Spring, Tiger River, Hot Spot, and Solana spa models The 2" measurement refers to the inner diameter of the most narrow part of the compression fitting/union The o-ring that is included measures ...read more -
Sku: 71036Compression Fitting, 2in with O-Ring
This 2" compression fitting, which includes the o ring, is sometimes referred to as a pump union or compression coupling It is found on the suction side of most Wavemaster® XP2 or XP2e Series Jet Pumps Other compression fittings are the 71038 and 71037 ...read more -
Sku: 30237-x2-BYPCompression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 71038Compression Fitting, 1-1/2in with O-Ring
This 1-1/2" compression fitting, which includes the o ring, is sometimes referred to as a pump union or compression coupling It is found on the suction and/or discharge side of FMHP/CP Series Wavemaster® Jet Pumps 2" x 1-1/2" Compression Fitting click ...read more -
This 2" compression fitting, which includes the o ring, is sometimes referred to as a pump union or compression coupling 1-1/2" Compression Fitting 2" Compression Fitting -
This replacement compression fitting split nut (AKA Split Union Nut-2") is used to connect heaters on the 1993-1994 Hot Spot Z, all 1998-current Hot Spot models, Solana models beginning in 2000 and all 1992-1994 Tiger River spas It is designed in two half ...read more -
This barbed fitting is primarily used to connect 1/2" vinyl tubing to various places within the circulating/heating system or jets in a Hot Spring & Tiger River spa It simply glues into a 1/2" PVC coupling or elbow with regular PVC cement -
Sku: 010009Barbed adapter 1 in x 3/8 Spigot
Barbed adapter 1 inch by 3/8 inch 425-5010 BARB ADAP 1IN(1)3/8IN -
Sku: 73297Cap, Drain Valve Assembly
Drain valve black cap, washer and ring assembly used on 2004 forward Hot Spring and Tiger River spa models -
Barbed adapter which is 1/2" male threads on one end and 1/2" barbed on the other -
This barbed fitting is primarily used to connect 1/2" vinyl tubing to various places within the circulating/heating system of Hot Spring spa models -
Sku: 30586Barbed Adapter, 1/4in X 5/16in
This barbed adapter is used in various places but primarily in the Moto-Massage niche for the small silicone Moto-Massage Jet air tube to slip onto on pre-1997 Hot Spring spa models -
Sku: 30548Starite Compression Fitting, 1-1/2″
1-1/2" compression coupling assembly (pump union) for all Starite pumps used on Hot Spring spas -
Sku: 70846Connector 3/4in X 1/2in Barbed X Barbed
Connector, 3/4in X 1/2in, barbed X barbed Connects a 3/4" tube to a 1/2" tube -
This compression fitting (aka pump union, quick disconnect, coupling) is used on the discharge side of the Tiger River Wavemaster Pumps to ensure that the small Silentflo 5000 or 5002 circulation pump pulls water through the filter when the jet pump is off ...read more -
Sku: 71387Fitting, Comp 45 Degree with O-Ring
This is a 2" pump union with a 45 degree offset street fitting It is used to connect the jet pump to the plumbing of the spa and allows the plumbing to come towards the pump from a 45-degree angle It glues into a 2" female PVC slip fitting using PVC ...read more -
Barbed adapter which is 3/4" male threads on one end and 1/2" barbed on the other -
Sku: 301035Barbed Adapter, 432-007525
Barbed adapter -
This is a PVC adapter that has 1/2" male threads on one end and 3/8" barbed on the other Allows a 1/2" female fitting to be adapted to 3/8" tubing that has no fitting on the end -
Sku: 70825-BYPSnap Ring Pliers Tool, Smart Jet Diverter Valve
These snap ring ("c"-ring) pliers can be used to remove the snap ring on Smart Jet diverter valves (71494, 71495, 73768, 73769) found in most hot tubs Made of carbon steel and vinyl grip handles and comes with interchangable straight, 45 degree and 90 degree ...read more -
Sku: 73808Ozone Restrictor, Freshwater 3
Flow restrictor for the Freshwater III ozone unit used to reduce the ozone order and/or to eliminate any "burping" noise emanating from the spa Simply remove the air filter from your Freshwater unit and attach to this flow restrictor as shown in the picture ...read more -
Sku: 70088Elbow with 1/4″ Barbed Nipple
This kit includes a 90-degree elbow 3/4" barbed on one end and 3/4" female threads on the other Also included is a 1/4" nipple which is then glued into either side of the elbow All that is needed is a hole drilled into either side of the elbow using a ...read more -
Sku: 30694Cap, 2in Slip
This is a cap that can be used to cap off a 2" male slip fitting or a 2" PVC pipe, either rigid or flexible PVC primer and PVC cement should be used to attach this fitting -
Sku: 30693PVC Cap 1 1/2in Slip
This is a cap which can be used to cap off a 1 1/2" male slip fitting or a 1 1/2" PVC pipe, either rigid or flexible PVC primer and PVC cement should be used to attach this fitting -
This is a PVC adapter that has 1/4" male threads on one end and 3/8" barbed on the other Allows a 1/4" female fitting to be adapted to 3/8" tubing that has no fitting on the end -
This barbed adapter has a 1/2" barbed fitting on one end, and a 1/2" male pipe thread fitting on the other end Then on the side of it, it has a 1/4" barbed fitting -
Sku: 11200013 PORT END CAP
3-port end cap for a 3-port manifold
Showing 1–30 of 43 results