I would like to express how excellent this company is. I inherited a house with a 2007 Hotspring Aria hot tub. The spa hasn’t been operated in years and when I turned it on, it ran for about 10 minutes and died. I mean dead died. I knew absolutely nothing about hot tubs but with the excellent diagnosis videos, installation videos and superior phone support, I was able to replace the main control board, heater relay board, heater, circulation pump, the ozonator and all associated tubing. This took 4 1/2 hours over two days (I had to watch videos) but the spa runs like new! I had one question regarding the jumper voltage 18 or 12. I spoke with a technician and he was able to answer my question as well as helping me double check the voltages for the components on the relay board. I am handy with electronics and electricity and am comfortable working with 230 volts. Shipping was fast and as expected. I highly recommend BackYardPlus.On 06/28/2024 by F. R. (verified customer)
Plumbing: Barbed Adapter, Check Valve, Inlet, Reducer, Snap Ring, Union
Showing 1–30 of 46 results
-
Sku: 30237-x2-BYPCompression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 301488Sweep Pump Union, 2in Soc. 90 Degree
Two-inch SOC 90deg sweep pump union -
Sku: 1119401Pump Union, 45 Degree
Pump union (aka compression fitting) can be used to connect to any Wavemaster pump later than 1996 This union accepts a 2" PVC pipe and will attach to a 2" standard pump thread The fitting for the pipe is at a 45-degree angle -
Sku: 72701Hartford Loop Assembly
This retrofit kit is used to replace the air check valve that was used in some Hot Spring spa models This kit replaces the obsolete 72342 Check your serial number in the parts finder above to be sure this part is for your spa -
Sku: 70864Check Valve, Safety Suction
This check valve's function is to "open" when someone puts their hand over the jet pumps suction fitting within the filter intake This check valve will "open" drawing air into it from the equipment compartment, thereby stopping suction of the jet pump This ...read more -
This barbed fitting is primarily used to connect 1/2" vinyl tubing to various places within the circulating/heating system or jets in a Hot Spring & Tiger River spa It simply glues into a 1/2" PVC coupling or elbow with regular PVC cement -
Sku: 010009Barbed adapter 1 in x 3/8 Spigot
Barbed adapter 1 inch by 3/8 inch 425-5010 BARB ADAP 1IN(1)3/8IN -
Barbed adapter which is 1/2" male threads on one end and 1/2" barbed on the other -
This barbed fitting is primarily used to connect 1/2" vinyl tubing to various places within the circulating/heating system of Hot Spring spa models -
Reducer Bushing, 3/4" Spig x 1/2" Slip This bushing allows a 1/2" male slip fitting or 1/2" PVC pipe, rigid or flexible, to be adapted to fit in a 3/4" female slip fitting The connection should be made using PVC primer and cement -
Sku: 30586Barbed Adapter, 1/4in X 5/16in
This barbed adapter is used in various places but primarily in the Moto-Massage niche for the small silicone Moto-Massage Jet air tube to slip onto on pre-1997 Hot Spring spa models -
Sku: 70846Connector 3/4in X 1/2in Barbed X Barbed
Connector, 3/4in X 1/2in, barbed X barbed Connects a 3/4" tube to a 1/2" tube -
This compression fitting (aka pump union, quick disconnect, coupling) is used on the discharge side of the Tiger River Wavemaster Pumps to ensure that the small Silentflo 5000 or 5002 circulation pump pulls water through the filter when the jet pump is off ...read more -
Sku: 31288Reducer, 2in X 1-1/2in Spig X Slip
Reducer Bushing, 2" Spig x 1-1/2" Slip This bushing allows for a 1 1/2" male slip fitting or PVC pipe, rigid or flexible, to connect to a 2" female slip fitting The connection should be made using PVC primer and cement -
Reducing Bushing, 1"Spig X 1/2" Slip This bushing allows a 1/2" male slip fitting or 1/2" PVC pipe, rigid or flexible, to be adapted to fit in a 1" female slip fitting The connection should be made using PVC primer and cement -
Sku: 70906Elbow/Union Assembly, Hot Spot
This assembly is used in two places on the 1993-1994 Hot Spot equipment compartment One of these assemblies connects onto the discharge (top) of the Wavemaster 3000 jet pump and the other end connects onto one side of the heater The second place is on the ...read more -
Reducer Bushing, 1" Spig x 3/4" Slip This bushing allows a 3/4" male slip fitting or 3/4" PVC pipe, rigid or flexible, to be adapted to fit in a 1" female slip fitting The connection should be made using PVC primer and cement -
Barbed adapter which is 3/4" male threads on one end and 1/2" barbed on the other -
Sku: 30667Coupling, Reducer 1in X 3/4in Sxs
This adapter is used to join a 3/4" PVC male fitting and a 1" PVC male fitting together PVC primer and cement should be used to adhere the fittings -
Sku: 301035Barbed Adapter, 432-007525
Barbed adapter -
Sku: 75001Pump Inlet Assembly, Grandee
The three pieces of this pump inlet assembly come pre-assembled and include the check valve This assembly was used on the jet pump on the 1989-1990 Hot Spring Grandee (G 191001 to G 109999) -
Sku: 75010Inlet Assembly with Check Valve
The four pieces of this pump inlet assembly come pre-assembled and include the check valve This assembly was used on the jet pump on the 1989 Hot Spring Jetsetter, Prodigy, and Sovereign Also used on the 1991-1992 Grandee -
This is a PVC adapter that has 1/2" male threads on one end and 3/8" barbed on the other Allows a 1/2" female fitting to be adapted to 3/8" tubing that has no fitting on the end -
Sku: 37681Red Bushing, 2in X 3/4in (437-248)
Reducer Bushing, 2" Spig x 3/4" Slip This bushing allows a 3/4" male slip fitting or 3/4" PVC pipe, rigid or flexible, to be adapted to fit in a 2" female slip fitting The connection should be made using PVC primer and cement -
Sku: 70825-BYPSnap Ring Pliers Tool, Smart Jet Diverter Valve
These snap ring ("c"-ring) pliers can be used to remove the snap ring on Smart Jet diverter valves (71494, 71495, 73768, 73769) found in most hot tubs Made of carbon steel and vinyl grip handles and comes with interchangable straight, 45 degree and 90 degree ...read more -
Reducer Bushing 1-1/2" Spig x 3/4 female iron pipe thread This bushing allows a 3/4" male pipe threaded fitting to be adapted to fit in a 1 1/2" female slip fitting The connection should be made using PVC primer and cement on the slip portion of the ...read more -
Reducer Bushing, 1-1/2" Spig x 1-1/4" Slip This bushing reduces a 1 1/2" female slip fitting down to a 1 1/4" female slip fitting PVC primer and cement should be used to glue the bushing in place -
Reducer Bushing, 1-1/4" Spig x 3/4" Slip This bushing allows a 3/4" male slip fitting or 3/4" PVC pipe, rigid or flexible, to be adapted to fit in a 1 1/4" female slip fitting The connection should be made using PVC primer and cement -
Sku: 30666Coupling, Reducer 3/4in X 1/2in Sxs
This is a PVC coupler that allows two PVC pipes to be joined together using PVC primer and cement One side of the coupler accepts a 1/2" PVC pipe, either rigid or flexible, and the other side accepts a 3/4" PVC pipe, either rigid or flexible
Showing 1–30 of 46 results