Love Backyard plus! I ordered the parts that I needed and they show up in record time. Can’t have a hot tub down in the middle of the winter. Only took 5 days. Really appreciate the serial number matching and schematics. Diagnostic help also.On 12/21/2023 by A. J. (verified customer)
Showing 91–120 of 148 results
-
Wavemaster 7000 (v 1) suction cover (volute) is the front half of the "wet end" (suction side) It has a square flange that accepts the adapter to connect to the plumbing of the spa Used on Hot Springs spas from 1993 to 1996
-
Sku: 72461
Power Cord, Wavemaster, 2-Speed
This power cord is a 14/4 (60" long) with flag terminals on both ends The cord has four wires inside which are BLACK, RED, WHITE, GREEN and is used on the two speed Wavemaster Jet Pumps -
Sku: 30225
Start Capacitor, Starite 1HP
Start capacitor used on all Sta-rite 1Hp Max-E-Glas jet pumps found on pre-1994 Hot Spring Grandee, Classic, Indoor/Outdoor, and Sovereign spa models -
Lock washer for the diffuser screw on a Wavemaster 7000 (ver 2) and Wavemaster 9000 jet pump
-
Sku: 70126
Pump Mounting Bracket, Starite 2HP
Pump mounting bracket used to secure the 2HP Sta-rite Max-E-Glas jet pump to the floor of the Hot Spring equipment compartment -
Sku: 70031
Pump Mounting Bracket, Starite 1HP
Pump mounting bracket used to secure the 1HP Sta-rite Max-E-Glas jet pump to the floor of the Hot Spring equipment compartment -
Sku: 70946
Impeller Screw, Wavemaster 9000
This stainless steel screw holds the impeller onto the Wavemaster 9000 jet pump shaft -
Flat Volute washer for the Wavemaster 7000 version 2 and he Wavemaster 9000
-
Sku: 73740
Leak Detection Kit
For Technicians Only Leak detection kit for Hot Spring, Hot Spot, and Limelight models -
Sku: Ceramic-Disk-BYP
Ceramic Pump Seal Disk
This ceramic piece is part of most pump seal kits -
Sku: 71400
Motor, 1.5Hp, XP
This is a replacement motor for a Wavemaster 5000 used on Tiger River and Hotsprings spas It can be wired 110 volts or 220 volts and is a single speed motor Will accept 48y frame wet ends -
Sku: 70959
Base, Wavemaster 9000
Black plastic base that serves two purposes: The first is to support the pump & motor and the second is to secure the base to the equipment compartment floor If you have a 48 frame pump, you will need the rubber pad 70958 that inserts/sits in the plastic ...read more -
This hex screw runs through the flange of the motor into the seal plate on a Wavemaster 7000, second version and a Wavemaster 9000 jet pump They are used to hold the seal plate in place against the motor
-
This stainless steel screw secures the diffuser to the seal plate on the Wavemaster 7000 second version and the Wavemaster 9000 jet pump
-
Bolt that secures the suction flange onto the front of the Wavemaster 7000 (v 1)
-
Sku: 70121
Run Capacitor, Starite 2HP
Run capacitor used on all 2HP Starite Max-E-Glas jet pumps on Hot Spring spas -
Sku: 30549
Union, 1-1/2in Slip x Threaded
Union, 1-1/2in slip x threaded -
This screw is used to secure the volute to the pump base 70959
-
Sku: 70958
Rubber Motor Pad, Wavemaster 9000
Rubber pad between the motor and the base to keep vibrations to a minimum It's used with item 70959 plastic pump base If you use a 48 frame pump, you need this rubber pad to fill the gap that is left between the motor and the base If you have a 56 frame ...read more -
One of two volute washers on the Wavemaster 7000 (second version) and the Wavemaster 9000 jet pump
-
This nut goes onto the volute bolt that secures the seal place to the volute
-
Sku: 77820
Pump Shroud
Pump shroud for 72991 jet pumps with vendor number 3536 -
Sku: 56WUA500-V
Wavemaster 9000/9200, 8000/8200 Volute O-Ring
LX MODEL O-RING Replacement volute o-ring (largest o-ring) for the Wavemaster pumps with vendor number 3536 (LX) This o-ring fits the 56-frame LX wet ends item 77713 and 77712 -
Sku: 48WUA-V
Wavemaster Volute O-Ring
LX MODEL O-RING Replacement volute o-ring (largest o-ring) for the Wavemaster pumps with vendor number 3536 (LX) This o-ring fits the 48-frame LX wet ends item 77711, 77710, and 77709 Stamped on wet-end: PP-GF30; B436-14 (03) Reference models (see ...read more -
Sku: 70032
Seal Plate, Starite
This Sta-rite seal plate is the part of the "wet end" that bolts onto the pump motor This seal plate is the replacement for both the 1hp and 2hp Starite Max-E-Glas jet pumps used on Hot Spring models prior to 1993 Note: Includes a new shaft seal and ...read more -
Sku: 70071
Insert, Seal Plate, Starite
Copper insert (heat sink) used on all 1HP and 2HP Starite Max-E-Glas jet pumps on Hot Spring spas Use with 30224 shaft seal -
Replacement Sta-rite impeller for the 2Hp pumps used on the Hot Spring Highlife prior to 1992
-
Obsolete: The volute and suction cover are no longer available separately and can only be purchased as a part of a wet end kit Please use parts finder serial number search engine to determine the correct wet end for your jet pump GECKO MODEL VOLUTE ...read more
-
Sku: 71693
Volute, Wavemaster (Gecko Model)
Obsolete: The volute and suction cover are no longer available separately and can only be purchased as a part of a wet end kit Please use parts finder serial number search engine to determine the correct wet end for your jet pump GECKO MODEL VOLUTE This ...read more -
Sku: 71029
Impeller, Wavemaster 7000 (ver. 2)
1 5 hp pump impeller for the Wavemaster 7000 (version 2) jet pump This impeller screws onto the pump motor's threaded shaft with regular right hand threads
Showing 91–120 of 148 results