Super service. Thank you.On 05/21/2024 by N. M. (verified customer)
Brand: Wavemaster 7000
Showing 31–52 of 52 results
-
Sku: 70399Seal Plate, Wavemaster 7000 (v.1)
The seal plate is the half of the "wet end" on the 1st version Wavemaster 7000 that bolts onto the pump motor -
Seal Plate for the Wavemaster 7000 version 2 and the Wavemaster 9000 -
Jet pump motor for the Wavemaster 7000 version 2 Specs: HP: 1 0 Frame: 48Y Voltage: 115/230 Speed: 1 Amperage: 7 0/14 0 SF: 1 65 Hz: 60 Base: Steel Reference: TPEE-WK03 -
Sku: 70411Tailpiece, Wavemaster 7000 (version 1)
Inside piece of the 2" compression fitting for a Wavemaster 7000 (v 1 and v 2) and a Wavemaster 9000 -
Sku: 70407GSKTVolute Suction Flange Gasket, Wavemaster 7000 (v.1)
Wavemaster 7000 (v 1) suction flange gasket This gasket fits between the volute cover and the square suction flange that accepts the adapter to connect to the plumbing of the spa Used on Hot Springs spas from 1993 to 1996 -
Wavemaster 7000 (v 1) suction cover (volute) is the front half of the "wet end" (suction side) It has a square flange that accepts the adapter to connect to the plumbing of the spa Used on Hot Springs spas from 1993 to 1996 -
This hex screw runs through the flange of the motor into the seal plate on a Wavemaster 7000, second version and a Wavemaster 9000 jet pump They are used to hold the seal plate in place against the motor -
This stainless steel screw secures the diffuser to the seal plate on the Wavemaster 7000 second version and the Wavemaster 9000 jet pump -
Bolt that secures the suction flange onto the front of the Wavemaster 7000 (v 1) -
OBSOLETE (Use the 35522-1, Except on '93-'96 Classic) This is the first version of the Wavemaster® 7000 jet pump This was the first 2" suction and discharge pump used on any Hot Spring model The pump hydraulics, as well as the entire jetting, plumbing ...read more -
Sku: 35522-1Pump, Wavemaster 7000 (ver. 2)
This is the second version of the Wavemaster® 7000 jet pump It was used on the 1995-1996 Hot Spring Grandee, Sovereign and the 1995-1996 Hot Spring 220volt only Sovereign (IH) model This pump can be used in place of 36070 -
Sku: 48WUA-VWavemaster Volute O-Ring
LX MODEL O-RING Replacement volute o-ring (largest o-ring) for the Wavemaster pumps with vendor number 3536 (LX) This o-ring fits the 48-frame LX wet ends item 77711, 77710, and 77709 Stamped on wet-end: PP-GF30; B436-14 (03) Reference models (see ...read more -
Sku: 71029Impeller, Wavemaster 7000 (ver. 2)
1 5 hp pump impeller for the Wavemaster 7000 (version 2) jet pump This impeller screws onto the pump motor's threaded shaft with regular right hand threads -
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com The V Clamp is a large stainless steel band that holds together the two halves (suction cover & seal ...read more -
Sku: 71027Steel Base, Wavemaster 7000 (ver. 2)
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com This black steel base supports the motor of the Wavemaster 7000 v 2 and bolts onto the floor of the Hot ...read more -
Sku: 70404Diffuser Screw, 8-32 X 1in Phillips, Wavemaster 7000 V1
This item is obsolete and replaced by:
70951Obsolete: Factory replacement suggestion item 70951 This is the screw that secures the diffuser to the seal plate on a Wavemaster 7000 (v 1) pump -
Sku: 35282Union Riser, Wavemaster 7000, V2
Obsolete: No factory suggested replacement available at this time Please contact our technicians at (805) 541-9000 or wizard@backyardplus com for advice Union riser is located on the suction & discharge of the Wavemaster 7000 version 2 This fitting ...read more -
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com The suction flange bolts onto the suction cover (front) of the Wavemaster 7000 (v 1) jet pump -
Use the 70400-BYP This shaft seal is for the Wavemaster 7000 (v 1) -
Sku: 34441Pump Shroud, Wavemaster 7000 (v.1)
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com This shroud attaches onto the rear of the pump motor Its purpose is to divert heated air from the motor ...read more -
Sku: 35283Compression Fitting O-Ring, Wavemaster 7000 V2, and 9000
This item is obsolete and replaced by:
34447Obsolete: Factory replacement suggestion item #34447 O-Ring Compression fitting o-ring (pump union) for all the Wavemaster 7000 (v 2) & Wavemaster 9000 (v 1) jet pumps -
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Wavemaster 7000 (v 1) metal base was used only on the 1996 Hot Spring Classic serial numbers from ...read more
Showing 31–52 of 52 results