After-Market Wet End Kit, Wavemaster 9000/9200 2.5 hp Pump

Item #: 72996-BYP
$118.87

This is the AFTER-MARKET “wet end” of the jet pump. Your Wavemaster 9000 & 9200 (v.2), 2.5 HP jet pump is comprised of two main components: the electric motor and the “wet end”. In some cases, this entire “wet end kit” is needed. Perfect remedy if your “wet end” has cracked since neither the volute (attaches to the motor) or the volute cover (front of the pump) are available individually from the manufacturer.

  • Add Bleedline Nipple Hot Spring/Solana/Hot Spot? (32267):

  • Add 2 Compression Fitting O-rings?

  • Add Bleedline Nipple Tiger River/Limelight? (33732):

  • Add Slinger (71551)

View OEM
SKU: 72996-BYP Categories: , Tags: , ,

Description

What’s Included: Volute, volute cover, volute o-ring, volute stainless steel screws, wear ring, impeller, and the shaft seal.

Description: This is the AFTER-MARKET “wet end” for the Wavemaster® 9000 & 9200, 2.5HP pump. This “wet end” will attach to your existing motor. Your Wavemaster 9000 & 9200 (v.2), 2.5 HP jet pump is comprised of two main components: the electric motor and the “wet end”. In some cases, this entire “wet end kit” is needed. Perfect remedy if your “wet end” has cracked since neither the volute (attaches to the motor) or the volute cover (front of the pump) are available individually from the manufacturer.

Installation: All “wet end kits” come pre-assembled from the factory. To install this kit you’ll disassemble it then re-assemble it one piece at a time onto your existing pump motor. Typical assembly time is two hours for the non-service tech. After connecting the pump unions (compression fittings) the pump may not align with the holes that anchor the pump to the floor of the equipment compartment. You may need to re-anchor using no longer than 1″ lag bolts. When pre-drilling for those bolts, do not pre-drill more than 1/4″ into the floor of the equipment compartment or you may drill into plumbing lines.

Important information for replacement parts:
Please check the vendor code or pump model on your pump before ordering replacement parts and use the chart to determine the correct wet-end replacement. If your vendor code reads “3536“, see item 77713.

Wet end will work the following pump models:
06125000-1040; 06025000-1040; 06025000-1040-B, 39578 or 0982601
Wet End Impeller Shaft Seal Wear Ring
72996-BYP* 71406-SW** 71447-BYP 71409-E

*Stamped on wet end leg: 92770705; Stamped on volute cover: 91231605
**71406-SW Dots: silver, white (use 71409-E wear ring)
If you can’t determine the dots on your impeller, buy the entire wet-end kit. The installation time is about the same.

View compatibility table & diagrams

You may also like…

  • Wet End Kit, Hot Spring, Hot Spot, Limelight
    This is the complete "wet end" of the jet pump Your Wavemaster 9000 & 9200 (v 2), 2 5 HP jet pump is comprised of two main components: the electric motor and the "wet end" In some cases, this entire "wet end kit" is needed Perfect remedy if your "wet ...read more
    $135.97
    Add to cart
  • Impeller, Wavemaster 9000/9200
    This impeller is used on the Wavemaster 9000 (ver 2), 9000 (ver 3) and Wavemaster 9200 jet pumps This impeller screws onto the pump motor's threaded shaft with regular right-hand threads
    $41.50
    Add to cart
  • Shaft Seal Kit, Wavemaster
    The shaft seal kit is used to prevent water from leaking from around the rotating pump shaft This seal kit is used on most of the Wavemaster and after-market jet pumps Please find your pump model number and if your pump is an OEM Wavemaster, you will also ...read more
    $17.63
    Add to cart