I would like to express how excellent this company is. I inherited a house with a 2007 Hotspring Aria hot tub. The spa hasn’t been operated in years and when I turned it on, it ran for about 10 minutes and died. I mean dead died. I knew absolutely nothing about hot tubs but with the excellent diagnosis videos, installation videos and superior phone support, I was able to replace the main control board, heater relay board, heater, circulation pump, the ozonator and all associated tubing. This took 4 1/2 hours over two days (I had to watch videos) but the spa runs like new! I had one question regarding the jumper voltage 18 or 12. I spoke with a technician and he was able to answer my question as well as helping me double check the voltages for the components on the relay board. I am handy with electronics and electricity and am comfortable working with 230 volts. Shipping was fast and as expected. I highly recommend BackYardPlus.On 06/28/2024 by F. R. (verified customer)
Find all the plumbing parts you need here. Flexi PVC tubing, Vinyl Tubing, Elbows, Tees, Diverter Valves, Levers & Bezels, Check-Valves, Couplers, and more.
Showing 1–30 of 80 results
-
This 2-position (3 and 9 o'clock) Smart Jet Water Diverter Valve Kit is located under the Smart Jet lever on the top lip of the spa Its purpose is to divert water to different jet combinations when you rotate the lever from 3 o'clock to 9 o'clock ...read more
-
This Smart Jet 4-position (3, 6, 9 and 12 o'clock)Water Diverter Valve is located under the Smart Jet lever/dial on the top lip of the spa Its purpose is to divert water to different jet combinations when you rotate the lever Replacement is necessary only ...read more
-
This valve retainer (sometimes called sleeve) is used as a retrofit to update the base of the Smart Jet on the 1998 Hot Spring and Tiger River spa models This will allow the replacement valve levers and bezels to fit since the 1998 valve lever and bezel are ...read more
-
Sku: 34350
Diverter Valve Snap Ring
This snap ring is used on most of the diverter valves on Hot Spring & Tiger River spas A special snap ring tool is needed to remove this part -
Order this item only if recommended to do so by our techs This modified 2-position (3 and 9 o'clock positions) Smart Jet Water Diverter Valve Kit is located under the Smart Jet lever/dial on the top lip of the spa Its purpose is to divert water to the ...read more
-
Order this item only if recommended to do so by our techs This modified 4-position Smart Jet Diverter Valve (12, 3, 6 and 9 o'clock positions) is located under the SmartJet lever on the top lip of the spa Its purpose is to divert water to different jet ...read more
-
This diverter valve is located under the diverter lever on the top lip of the spa Its purpose is to divert water to different jet combinations when you rotate the lever or dial Replacement is necessary only if the valve lever becomes too difficult to turn, ...read more
-
Sku: 36159
Precision Jet Elbow
This elbow is used to glue onto the rear of the Precision Jet Body This elbow is an odd size and is not available at the local hardware store -
Sku: 30237-x2-BYP
Compression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 301488
Sweep Pump Union, 2in Soc. 90 Degree
Two-inch SOC 90deg sweep pump union -
Sku: 1119401
Pump Union, 45 Degree
Pump union (aka compression fitting) can be used to connect to any Wavemaster pump later than 1996 This union accepts a 2" PVC pipe and will attach to a 2" standard pump thread The fitting for the pipe is at a 45-degree angle -
This plug has been used on the 220volt pre-1995 Hot Spring heater to cap off the drain hose by clamping the 1/4" vinyl drain tubing to the closed 1/4" nipple on this plug Also used in the 71557-BYP Kit
-
Sku: 37704
Diverter Body, 2-Port
This is a replacement valve body for 1994-2008 Hot Spring, Tiger River and all Limelight spa models with two-port diverter valves This valve body has 2" diameter ports and replaces the original black valve body -
Sku: 37297
6 Port Diverter Valve Body
This 6 port diverter valve body is used on the Hot Spring and Tiger River spa models that utilize a four-position valve -
Sku: 75112
Hot Spring Jet Selector Lever, Cool Gray
The cool gray colored Hot Spring jet selector lever is found on the 2009-2013 Hot Spring spas -
45 degree PVC elbow, 2", Spg X Slip
-
Sku: 34838
Elbow 1/2in Polybarb
This is a 1/2" 90-degree barbed elbow for use with clear 1/2" PVC tubing -
Sku: 38429
Water Manifold,1in X 1/2in 4-Port
Water Manifold, 1" x 1/2" 4-port -
Sku: 34391
Elbow, Street 90 2in Spig X Slip
This is a 2" 90-degree street elbow made of PVC plastic It has a male PVC fitting on one side, and on the other side, it has a female PVC slip fitting This allows for the elbow to be used in tighter spaces -
Sku: 30642
Elbow, 90 Degree 1/2in Slip X Slip
This elbow is used to join two 1/2" male PVC slip fittings or 1/2" rigid or flexible PVC pipes together at a 90-degree angle PVC primer and cement should be used to secure this fitting to the fittings it is joining together -
Sku: 300843
406-101 Red Elbow 3/4inX1/2in
Reducing 90-degree ell, 3/4" x 1/2", plumbing fitting -
Sku: 31932
Elbow, 90 Degree 2in Slip X Slip
This elbow is used to join two 2" male PVC slip fittings or 2" rigid or flexible PVC pipes together at a 90-degree angle PVC primer and cement should be used to secure this fitting to the fittings it is joining together -
Sku: 30643
Elbow, 90 Degree 3/4in Slip X Slip
This is a 3/4" 90-degree elbow made out of PVC which will accept two male 3/4" PVC flex or rigid pipes and join them together at a 90-degree angle using PVC primer and cement -
Sku: 34338
Manifold, Flow Cone
Manifold, flow cone -
Sku: 33021
Elbow, 90 Degree 1-1/4in X 1in
This elbow is used to join a 1 1/4" male PVC slip fitting or 1 1/4" rigid or flexible PVC pipe to a 1" male PVC slip fitting or 1" rigid or flexible PVC pipe at a 90-degree angle PVC primer and cement should be used to secure this fitting to the fittings ...read more -
Sku: 30650
Street Elbow, 90 3/4in Spig X Slip
This is a 3/4" 90-degree street elbow made of PVC plastic It has a male PVC fitting on one side, and on the other side, it has a female PVC slip fitting This allows for the elbow to be used in tighter spaces -
Sku: 39704
6-3/4 Port Water Manifold, 2in Slip PVC
PVC water manifold, 2" Slip x 6 Port 3/4" -
Sku: 30645
Elbow, 90 Degree 1-1/2in Slip X Slip
This elbow is used to join two 1 1/2" male PVC slip fittings or 1 1/2" rigid or flexible PVC pipes together at a 90-degree angle PVC primer and cement should be used to secure this fitting to the fittings it is joining together -
Sku: 39702
Manifold, Water, 2in X 1/2in, 6-Port
PVC water manifold, 2" X 1/2", 6-Port
Showing 1–30 of 80 results