It was very easy to select the corret parts for my "serial Number". All parts were correct and operated as required.On 06/20/2024 by M. R. (verified customer)
Find all the plumbing parts you need here. Flexi PVC tubing, Vinyl Tubing, Elbows, Tees, Diverter Valves, Levers & Bezels, Check-Valves, Couplers, and more.
Showing 1–30 of 105 results
-
This 2-position (3 and 9 o'clock) Smart Jet Water Diverter Valve Kit is located under the Smart Jet lever on the top lip of the spa Its purpose is to divert water to different jet combinations when you rotate the lever from 3 o'clock to 9 o'clock ...read more
-
This Smart Jet 4-position (3, 6, 9 and 12 o'clock)Water Diverter Valve is located under the Smart Jet lever/dial on the top lip of the spa Its purpose is to divert water to different jet combinations when you rotate the lever Replacement is necessary only ...read more
-
This valve retainer (sometimes called sleeve) is used as a retrofit to update the base of the Smart Jet on the 1998 Hot Spring and Tiger River spa models This will allow the replacement valve levers and bezels to fit since the 1998 valve lever and bezel are ...read more
-
Sku: 34350
Diverter Valve Snap Ring
This snap ring is used on most of the diverter valves on Hot Spring & Tiger River spas A special snap ring tool is needed to remove this part -
Order this item only if recommended to do so by our techs This modified 2-position (3 and 9 o'clock positions) Smart Jet Water Diverter Valve Kit is located under the Smart Jet lever/dial on the top lip of the spa Its purpose is to divert water to the ...read more
-
Order this item only if recommended to do so by our techs This modified 4-position Smart Jet Diverter Valve (12, 3, 6 and 9 o'clock positions) is located under the SmartJet lever on the top lip of the spa Its purpose is to divert water to different jet ...read more
-
This diverter valve is located under the diverter lever on the top lip of the spa Its purpose is to divert water to different jet combinations when you rotate the lever or dial Replacement is necessary only if the valve lever becomes too difficult to turn, ...read more
-
Sku: 36159
Precision Jet Elbow
This elbow is used to glue onto the rear of the Precision Jet Body This elbow is an odd size and is not available at the local hardware store -
Sku: 30237-x2-BYP
Compression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 32267-1
Drain Plug, Wavemaster
This drain plug is screwed into the female port on the front of Wavemaster 3000, Wavemaster 4000 and 6000 jet pumps when there is an absence of a bleedline For spas with a bleedline, the 32267 is used in place of this fitting This drain plug can be ...read more -
Sku: 301488
Sweep Pump Union, 2in Soc. 90 Degree
Two-inch SOC 90deg sweep pump union -
Sku: 1119401
Pump Union, 45 Degree
Pump union (aka compression fitting) can be used to connect to any Wavemaster pump later than 1996 This union accepts a 2" PVC pipe and will attach to a 2" standard pump thread The fitting for the pipe is at a 45-degree angle -
This plug has been used on the 220volt pre-1995 Hot Spring heater to cap off the drain hose by clamping the 1/4" vinyl drain tubing to the closed 1/4" nipple on this plug Also used in the 71557-BYP Kit
-
Sku: 37704
Diverter Body, 2-Port
This is a replacement valve body for 1994-2008 Hot Spring, Tiger River and all Limelight spa models with two-port diverter valves This valve body has 2" diameter ports and replaces the original black valve body -
Sku: 37297
6 Port Diverter Valve Body
This 6 port diverter valve body is used on the Hot Spring and Tiger River spa models that utilize a four-position valve -
This 2-position (3 and 9 o'clock) Diverter Valve Kit is located under the diverter lever on the top lip of the spa Its purpose is to divert water to different jet combinations when you rotate the lever from 3 o'clock to 9 o'clock Replacement is necessary ...read more
-
Sku: 11080
449-020 2in Plug
This is a 2" PVC plug It can be used to plug any 2" female PVC fitting and should be installed using PVC primer and cement You can get PVC cement at your local hardware store -
Sku: 75112
Hot Spring Jet Selector Lever, Cool Gray
The cool gray colored Hot Spring jet selector lever is found on the 2009-2013 Hot Spring spas -
45 degree PVC elbow, 2", Spg X Slip
-
Sku: 34838
Elbow 1/2in Polybarb
This is a 1/2" 90-degree barbed elbow for use with clear 1/2" PVC tubing -
Sku: 38429
Water Manifold,1in X 1/2in 4-Port
Water Manifold, 1" x 1/2" 4-port -
Sku: 34391
Elbow, Street 90 2in Spig X Slip
This is a 2" 90-degree street elbow made of PVC plastic It has a male PVC fitting on one side, and on the other side, it has a female PVC slip fitting This allows for the elbow to be used in tighter spaces -
Sku: 30642
Elbow, 90 Degree 1/2in Slip X Slip
This elbow is used to join two 1/2" male PVC slip fittings or 1/2" rigid or flexible PVC pipes together at a 90-degree angle PVC primer and cement should be used to secure this fitting to the fittings it is joining together -
Sku: 300843
406-101 Red Elbow 3/4inX1/2in
Reducing 90-degree ell, 3/4" x 1/2", plumbing fitting -
Sku: 31932
Elbow, 90 Degree 2in Slip X Slip
This elbow is used to join two 2" male PVC slip fittings or 2" rigid or flexible PVC pipes together at a 90-degree angle PVC primer and cement should be used to secure this fitting to the fittings it is joining together -
Sku: 30643
Elbow, 90 Degree 3/4in Slip X Slip
This is a 3/4" 90-degree elbow made out of PVC which will accept two male 3/4" PVC flex or rigid pipes and join them together at a 90-degree angle using PVC primer and cement -
Sku: 34338
Manifold, Flow Cone
Manifold, flow cone -
Sku: 33021
Elbow, 90 Degree 1-1/4in X 1in
This elbow is used to join a 1 1/4" male PVC slip fitting or 1 1/4" rigid or flexible PVC pipe to a 1" male PVC slip fitting or 1" rigid or flexible PVC pipe at a 90-degree angle PVC primer and cement should be used to secure this fitting to the fittings ...read more -
Sku: 30650
Street Elbow, 90 3/4in Spig X Slip
This is a 3/4" 90-degree street elbow made of PVC plastic It has a male PVC fitting on one side, and on the other side, it has a female PVC slip fitting This allows for the elbow to be used in tighter spaces
Showing 1–30 of 105 results