The team at Backyardplus.com are the best for anything Hot Springs. Super friendly and knowledgeable.On 06/05/2024 by S. O. (verified customer)
Find all the plumbing parts you need here. Flexi PVC tubing, Vinyl Tubing, Elbows, Tees, Diverter Valves, Levers & Bezels, Check-Valves, Couplers, and more.
Showing 1–30 of 81 results
-
Sku: 1044101-72228-AM-BYP
Tubing Kit, Del-Ozone-1/4in with Check valve
This 1/4" ID (3/8" OD) ozone-resistant tubing works with UO3 ozone generator It includes an attached 1/4" ozone-resistant check valve, clamps, mounting screws, and new flag terminals This assembly is approx five feet in length Note: There is a small ...read more -
Sku: 1044101-72228-BYP
Tubing Kit, Freshwater III Ozonator-1/4in Tygon/Kynar with Check valve
This 1/4" ID (3/8" OD) Kynar/Tygon ozone-resistant tubing kit comes standard with the Freshwater III Ozonators It is the replacement for all Freshwater 3 ozonators It includes an attached 1/4" ozone-resistant check valve This assembly is approx six feet ...read more -
Sku: 35233
Water Check Valve, 3/4 inch
This 3/4" water check valve is installed in the inlet side of the circulation pumps plumbing to prevent the backflow of water through the circulation pump once the jet pump is activated All water check valves have arrows stamped on the outside to indicate ...read more -
This 2-position (3 and 9 o'clock) Smart Jet Water Diverter Valve Kit is located under the Smart Jet lever on the top lip of the spa Its purpose is to divert water to different jet combinations when you rotate the lever from 3 o'clock to 9 o'clock ...read more
-
This Smart Jet 4-position (3, 6, 9 and 12 o'clock)Water Diverter Valve is located under the Smart Jet lever/dial on the top lip of the spa Its purpose is to divert water to different jet combinations when you rotate the lever Replacement is necessary only ...read more
-
This valve retainer (sometimes called sleeve) is used as a retrofit to update the base of the Smart Jet on the 1998 Hot Spring and Tiger River spa models This will allow the replacement valve levers and bezels to fit since the 1998 valve lever and bezel are ...read more
-
Air check valve for Hot Spring, Tiger River, and Hot Spot spa models This check valve is located in the equipment compartment under the bartop Its primary function is to prevent water from back flowing into the equipment compartment should a hydrotherapy ...read more
-
Order this item only if recommended to do so by our techs This modified 2-position (3 and 9 o'clock positions) Smart Jet Water Diverter Valve Kit is located under the Smart Jet lever/dial on the top lip of the spa Its purpose is to divert water to the ...read more
-
Order this item only if recommended to do so by our techs This modified 4-position Smart Jet Diverter Valve (12, 3, 6 and 9 o'clock positions) is located under the SmartJet lever on the top lip of the spa Its purpose is to divert water to different jet ...read more
-
This diverter valve is located under the diverter lever on the top lip of the spa Its purpose is to divert water to different jet combinations when you rotate the lever or dial Replacement is necessary only if the valve lever becomes too difficult to turn, ...read more
-
Sku: 38390
Check Valve, Air, with Ball 1/2in
It is used to prevent water from backing into the airlines when the jets are off It is at the back of the Moto-Massage housing and glued into a 90-degree elbow It is also on the jetstream jets -
Sku: 1044101
Check Valve (Ozone) Freshwater Ozone, 1/4in O.D.
Over time an Ozonator check valve will breakdown under the harsh conditions of ozone Our OEM check valves have a special diaphragm (Viton) that enables them to last longer than rubber Rubber diaphragms last about a month before the rubber becomes hard -
Sku: 36160
Precision Jet Tee
This tee is used to glue onto the rear of the Precision Jet Body and provides a 1/2" connection on either side of the tee This tee is not available at the local hardware store -
Sku: 37704
Diverter Body, 2-Port
This is a replacement valve body for 1994-2008 Hot Spring, Tiger River and all Limelight spa models with two-port diverter valves This valve body has 2" diameter ports and replaces the original black valve body -
This 2-position (3 and 9 o'clock) Diverter Valve Kit is located under the diverter lever on the top lip of the spa Its purpose is to divert water to different jet combinations when you rotate the lever from 3 o'clock to 9 o'clock Replacement is necessary ...read more
-
This air check valve is located in the equipment compartment, up high, under the bar top If a hydrotherapy jet should become obstructed (like when a guest sticks their finger in the jet), this item becomes critical in preventing water from back flowing into ...read more
-
Sku: 72701
Hartford Loop Assembly
This retrofit kit is used to replace the air check valve that was used in some Hot Spring spa models This kit replaces the obsolete 72342 Check your serial number in the parts finder above to be sure this part is for your spa -
Sku: 70425
Bypass Tee
This assembly is found on all Tiger River spas This 3/4" x 1/2" tee has 3/4" male barbed fittings on each end and a 1/2" barbed male fitting on the elbow It is located in front of the circulation pump between the check valve (35233) and the inlet of the ...read more -
This "Jet System" check valve is used on all Hot Spring models and all Tiger River spas This check valve engages when the diverter valve is changed to different positions For convenience, the inside diameter of this check valve is 1-1/2" and the outside ...read more
-
Sku: 30490
Wallfitting, Rear
This fitting is used on many different Hot Spring spa models in various places including the grill style filter compartment as part of the filter assembly Also used in the filter compartment of all 1992-1996 Tiger River spa models -
Sku: 75112
Hot Spring Jet Selector Lever, Cool Gray
The cool gray colored Hot Spring jet selector lever is found on the 2009-2013 Hot Spring spas -
Sku: 70864
Check Valve, Safety Suction
This check valve's function is to "open" when someone puts their hand over the jet pumps suction fitting within the filter intake This check valve will "open" drawing air into it from the equipment compartment, thereby stopping suction of the jet pump This ...read more -
Barbed tee 1/4" on all three sides Used with 1/4" vinyl tubing and 1/4" clamps
-
This threaded wall fitting is located in the bottom of the filter compartment on all 1997-2010 Tiger River Bengal, Caspian, Sumatran & Siberian spa models This is where the filter standpipe screws into
-
Sku: 71981
Check Valve, with Spring, 1-1/2in
1-1/2" spring style check valve is commonly found between the jet pump and filter housing on Tiger River spas This check valve automatically closes when the Tiger River spas jet pump is turned off so the circulation pump (Silentflo 5000) can then draw water ...read more -
Sku: 31487
Tee, 1/2in X 1/2in Barb
Tee, Barbed, Black Poly, 1/2" x 1/2" x 1/2" -
Sku: 30626
Tee, 1/2in Slip X Slip X Slip
This PVC tee will accept 1/2" male rigid or flexible PVC pipe or male PVC fittings 1/2" schedule 40 thick-walled clear vinyl PVC can also be glued directly to this fitting PVC primer and cement should be used on this fitting Failing to use primer ...read more -
Sku: 34458
Red Tee 2in X 1-1/2in X 1-1/2in
PVC tee, 2" X 1-1/2" X 1-1/2" slip -
Sku: 72185
Diverter valve Tee
Tee for 2 position diverter valve -
Sku: 32465
Tee 2in
This tee allows three 2" male PVC slip connections, or 2" PVC pipe (rigid or flexible) to be joined together, one of which is perpendicular to the other two connections PVC primer and glue should be used to adhere to the male connections tog the fitting
Showing 1–30 of 81 results