I would like to express how excellent this company is. I inherited a house with a 2007 Hotspring Aria hot tub. The spa hasn’t been operated in years and when I turned it on, it ran for about 10 minutes and died. I mean dead died. I knew absolutely nothing about hot tubs but with the excellent diagnosis videos, installation videos and superior phone support, I was able to replace the main control board, heater relay board, heater, circulation pump, the ozonator and all associated tubing. This took 4 1/2 hours over two days (I had to watch videos) but the spa runs like new! I had one question regarding the jumper voltage 18 or 12. I spoke with a technician and he was able to answer my question as well as helping me double check the voltages for the components on the relay board. I am handy with electronics and electricity and am comfortable working with 230 volts. Shipping was fast and as expected. I highly recommend BackYardPlus.On 06/28/2024 by F. R. (verified customer)
Plumbing: Compression Fitting, Handles Knobs Levers Bezels, Nipple, Ring, Snap Ring, Water Manifold
Showing 1–30 of 39 results
-
Sku: 34447-x2-BYPCompression Fitting O-rings, for 2 inch Union (Qty of 2)
(Quantity of 2 o-rings) O-rings used on the pumps 2" compression fittings ( 71036 ) found on most Hot Spring, Tiger River, Limelight, Hot Spot and Solana spa models Also used on the replacement "Wet End" pump kits and some heaters The 2" measurement refers ...read more -
O-ring used on the 2" compression fittings (71036) on most Hot Spring, Tiger River, Hot Spot, and Solana spa models The 2" measurement refers to the inner diameter of the most narrow part of the compression fitting/union The o-ring that is included measures ...read more -
Sku: 71036Compression Fitting, 2in with O-Ring
This 2" compression fitting, which includes the o ring, is sometimes referred to as a pump union or compression coupling It is found on the suction side of most Wavemaster® XP2 or XP2e Series Jet Pumps Other compression fittings are the 71038 and 71037 ...read more -
Sku: 30237-x2-BYPCompression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 71038Compression Fitting, 1-1/2in with O-Ring
This 1-1/2" compression fitting, which includes the o ring, is sometimes referred to as a pump union or compression coupling It is found on the suction and/or discharge side of FMHP/CP Series Wavemaster® Jet Pumps 2" x 1-1/2" Compression Fitting click ...read more -
This 2" compression fitting, which includes the o ring, is sometimes referred to as a pump union or compression coupling 1-1/2" Compression Fitting 2" Compression Fitting -
This replacement compression fitting split nut (AKA Split Union Nut-2") is used to connect heaters on the 1993-1994 Hot Spot Z, all 1998-current Hot Spot models, Solana models beginning in 2000 and all 1992-1994 Tiger River spas It is designed in two half ...read more -
Sku: 38429Water Manifold,1in X 1/2in 4-Port
Water Manifold, 1" x 1/2" 4-port -
Sku: 34338Manifold, Flow Cone
Manifold, flow cone -
Sku: 30548Starite Compression Fitting, 1-1/2″
1-1/2" compression coupling assembly (pump union) for all Starite pumps used on Hot Spring spas -
Sku: 397046-3/4 Port Water Manifold, 2in Slip PVC
PVC water manifold, 2" Slip x 6 Port 3/4" -
This compression fitting (aka pump union, quick disconnect, coupling) is used on the discharge side of the Tiger River Wavemaster Pumps to ensure that the small Silentflo 5000 or 5002 circulation pump pulls water through the filter when the jet pump is off ...read more -
Sku: 39702Manifold, Water, 2in X 1/2in, 6-Port
PVC water manifold, 2" X 1/2", 6-Port -
Sku: 71387Fitting, Comp 45 Degree with O-Ring
This is a 2" pump union with a 45 degree offset street fitting It is used to connect the jet pump to the plumbing of the spa and allows the plumbing to come towards the pump from a 45-degree angle It glues into a 2" female PVC slip fitting using PVC ...read more -
Sku: 300042Manifold, 2 Port, 3/4in X 1/2in X 1/2in
Wye manifold with 3/4" slip inlet to two 1/2" slip outlets Used on Hot Spring, Tiger River, Hot Spot & Solana spa models PVC cement and primer should be used to make the connections to this manifold -
Sku: 301235Manifold 1.5in X X 1.5in SP X (4)
Manifold, 1 5inch slip by 1 5 SP x 4 -
PVC water manifold, 1-1/2" X 1/2", 6-Port -
Sku: 10566018 Port Manifold, 2-1/2in x 3/4in
This is a manifold with 2-1/2" slip inlet to eight 3/4" slip outlets It can be used with rigid or flexible PVC piping or male PVC slip fittings PVC primer and cement should be used to adhere to the connections -
Sku: 70825-BYPSnap Ring Pliers Tool, Smart Jet Diverter Valve
These snap ring ("c"-ring) pliers can be used to remove the snap ring on Smart Jet diverter valves (71494, 71495, 73768, 73769) found in most hot tubs Made of carbon steel and vinyl grip handles and comes with interchangable straight, 45 degree and 90 degree ...read more -
Sku: 010020Four Barbed Water Manifold
Four barbed water manifold (MANIFOLD 4 BARB 1INX3/8IN) for Hot Spring, Hot Spot, and Limelight models -
Sku: 010004Four Port Water Manifold
Four port water manifold for Hot Spring, Hot Spot and Limelight models MANIFOLD 2S/2SP/4-PORT 1/2 -
Sku: 70088Elbow with 1/4″ Barbed Nipple
This kit includes a 90-degree elbow 3/4" barbed on one end and 3/4" female threads on the other Also included is a 1/4" nipple which is then glued into either side of the elbow All that is needed is a hole drilled into either side of the elbow using a ...read more -
Sku: 10012Manifold, 2 Port 1 S 1/2in S X 3/4in
This 2 port manifold is made of white PVC and is used to connect a 1 1/2" PVC pipe, either flexible or rigid, to two 3/4" PVC pipes, also either rigid or flexible The connections should be made using PVC primer and cement -
Sku: 010007Manifold, 2S x 2S X 1/2″ (4) Port
Water Manifold, 2" x 2" x 1/2" 4-Port -
Sku: 010016Manifold, 4 Port , 1-1/2″ X 3/4″
Water manifold with 1-1/2" inlet and four 3/4" outlet ports Used in various spa models within the Watkins family Use pvc primer and pvc cement when gluing either flexible or rigid pvc to this manifold -
Sku: 010018Manifold, Water, 1-1/2″ X 3/4″ (6 Port)
This six-port manifold is made of white PVC and is used to connect a 1 1/2" PVC pipe, either flexible or rigid, to six 3/4" PVC pipes, also either rigid or flexible The connections should be made using PVC primer and cement -
Sku: 010005Manifold, Water, 2″ X 2″ x 3/4″ (6 Port)
This six-port water manifold is made of white PVC and is used to connect a 2" PVC pipe, either flexible or rigid, to six 3/4" PVC pipes, also either rigid or flexible The connections should be made using PVC primer and cement -
Sku: 010013Manifold, Water, 2″ X 3/4″, 5 Port
This five port manifold is made of white PVC and is used to connect a 2" PVC pipe, either flexible or rigid, to five 3/4" PVC pipes, also either rigid or flexible The connections should be made using PVC primer and cement -
Sku: 010001Ten Port Water Manifold
Ten port water manifold for Hot Spring, Hot Spot and Limelight models MAN 1 5S/1 5SP/10-PORT 1/2
Showing 1–30 of 39 results