It was very easy to select the corret parts for my "serial Number". All parts were correct and operated as required.On 06/20/2024 by M. R. (verified customer)
Showing 1–30 of 55 results
-
Sku: 300055
Spring Clamp, 3/4 inch
3/4" spring clamp (aka wire clamp) is used to secure the 3/4 inch vinyl tubing (70315) to various components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers or hose clamp pliers to ...read more -
"Blade Mount" pillow retainer (set of two blades) for all Hot Spring spa pillows and all Limelight spa pillows beginning in the second quarter of 2007 Check the diagrams for the correct pillow retainer
-
Sku: 31134
Spring Clamp, 1/4in
Used to secure 1/4" (ID) vinyl tubing 70318 (OD measure 7/16") to various components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers or hose clamp pliers to squeeze, then slide this ...read more -
Sku: 37112
O-Ring, Precision Jet
Precision Jet o-ring fits between the interior spa shell and the wall fitting nut to prevent leaks from around the jet The o-ring creates a seal between the jet body and the back of the shell when compressed by the wall fitting nut -
This stainless steel screw is used to secure the Moto-Massage faceplate to its guide body on many Hot Spring and Solana spa models Also used on the 1995-1999 Hot Spring Dream Pillow Jet Check your serial number in the parts finder to be sure this part ...read more
-
Sku: 71410-BYP
Volute O-Ring, Wavemaster
This is the largest O-ring used on the current Wavemaster series of wet ends for Hot Springs, Tiger River, Limelight, Solana and Hot Spot model spas This o-ring fits between the suction cover and the volute of the pump series: XP2/XP2E This o-ring is only ...read more -
Sku: 71554
Wavemaster Volute O-Ring
GECKO MODEL O-RING Replacement o ring (largest o-ring) for the Wavemaster 4000, 6000, 8000 (ver 3), 8200, 9000 (ver 3), 9200 jet pumps Will fit on pump series: XP2/XP2e -
GECKO MODEL SCREW This stainless steel screw is used to attach the volute cover to the volute on most Wavemaster jet pumps
-
Sku: 34447-x2-BYP
Compression Fitting O-rings, for 2 inch Union (Qty of 2)
(Quantity of 2 o-rings) O-rings used on the pumps 2" compression fittings ( 71036 ) found on most Hot Spring, Tiger River, Limelight, Hot Spot and Solana spa models Also used on the replacement "Wet End" pump kits and some heaters The 2" measurement refers ...read more -
O-ring used on the 2" compression fittings (71036) on most Hot Spring, Tiger River, Hot Spot, and Solana spa models The 2" measurement refers to the inner diameter of the most narrow part of the compression fitting/union The o-ring that is included measures ...read more
-
Sku: 30018
Mounting Bolt, Wavemaster
1/4-20 X 1-1/4" long mounting bolt that secures the pump to the floor of the equipment compartment Used on the Wavemaster 4000, Wavemaster 6000 and Wavemaster 7000 3 jet pumps -
Sku: 30413
Mounting Bolt Washer, Wavemaster
Stainless steel washer used with the bolts that secure a pump to the pump stand and the pump stand to the floor of the equipment compartment 5/16" -
Sku: 31228
Spring Clamp, 1/2in
1/2" spring clamp for securing 1/2" ID vinyl tubing (70316) to components Item 70316 has an inner diameter of 1/2" and an outer diameter of 3/4" This clamp fits the 3/4" OD Note: Wear eye protection when squeezing these little rascals Service techs ...read more -
Sku: 34465
Spring Clamp, 3/8in
3/8" spring clamp (aka wire clamp) is used to secure the 3/8 inch vinyl tubing 70317 (9/16" OD) to various components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers are hose clamp ...read more -
Sku: 72574
Hardware Bag #1, Cover Cradle
This Cover Cradle & Cover Cradle II hardware bag #1 includes the following: Four Hole Side Hinge (Qty 2) Four Hole Rear Hinge (Qty 2) #10 x 1" Flat Head Screws (Qty 8) #10 x 1-1/2" Flat Head Screws (Qty 8) Note: The items in this hardware bag are ...read more -
Sku: 302637
Door Screw, Hot Spot
This screw is used to attach the door(s) on all Hot Spot spas beginning in 2003 that use wood or synthetic wood siding: 1/4-20 x 1-3/4" Truss stainless steel Phillips head screw Price is per individual screw This part number replaces the obsolete 1-1/2" ...read more -
Sku: 36534
Gasket, Jet Face
This black rectangle rubber gasket fits inside of the jet face on Hot Spring, Tiger River, Hot Spot, and Solana spa models This gasket creates the seal for the air adjustment of the jet This gasket failing will not cause the spa to leak -
Sku: 300040
Brass Door Screw Insert, 1/4in
This brass insert is used on the door frames of various spa models to provide attach a door using a stainless steel screw which screws into this insert -
This ball stud is found on 3rd quarter 2009 and newer UpRite, Cover Cradle and Cover Cradle II lifters The older cover lifters used a 1/4" threaded shaft ball stud which is part# 71107-BYP
-
Sku: 30334
Screw, #4 X 1/2in Stainless Steel
Stainless steel screw used in various locations on Hot Spring, Tiger River, Solana, Hot Spot and Limelight spas -
Sku: 72775-x1-BYP
Intake Vent Screen
This aluminum perforated strip mounts at the bottom of the equipment access door to keep rodents from making their home in the warmth of your Hot Spring or Tiger River spas equipment compartment This screen is cut to length Not available for the Hot Spring ...read more -
Sku: 71892
Screw 10-24 X 3/4in with Cap Retainer
Six of these screws are used on the Solana TX made from 2000 to 2010 to hold the equipment door in place These stainless steel screws are unique in that they come with a plastic retainer that surrounds the head of the screw designed to accept a plastic ...read more -
Sku: 1386701
GFCI Inline, 15A. 115v. w/ 90 Degree Plug End
This new style 15amp GFCI is molded onto the power cord and has a 90-degree plug end It is the newest factory replacement for 15 amp Solana and Hot Spot spa models -
Sku: 35986
O-Ring, Adj/Jet Small, Hot Spring
Small o-ring used on various jets -
Wall fitting nut o-ring
-
Sku: 73557
Screw Cover Cream
Six of these screw covers are used to hold the equipment door in place on the Hot Spot TX from 2005 to 2010 These cream-colored caps attach to a plastic retainer that surrounds the head of the screw used to hold the door panel in place to provide a more ...read more -
Sku: 72714
Hardware Bag #2, Cover Cradle II
This Cover Cradle II hardware bag #2 includes the following: 1/4"-20 x 3/4" Stainless Steel Hex Bolts (Qty 4) #10 x 1-1/2" Stainless Steel Flat Head Screws (Qty 8) #10 x 1-1/2" Stainless Steel Pan Head Screws (Qty 14) Note: The items in this hardware ...read more -
Sku: 71893
Screw Cover, Equipment Door, TX, Taupe
Six of these round screw covers are used on the Solana TX made from 2000-2004 to hold the equipment door in place These taupe-colored caps attach to a plastic retainer that surrounds the head of the screw used to hold the door panel in place to provide a ...read more -
Sku: 20120
Control Box Power Cord, Heavy Duty 20amp
This extreme weather, heavy-duty 20amp 120volt power cord is used with the 20amp GFCI on 120volt Hot Spring, Tiger River, Solana, and Hot Spot spa models -
Sku: 74888-1
Multizone Lighting Bayonet Sleeves
Multizone lighting bayonet sleeves, quantity of 1
Showing 1–30 of 55 results