I would like to express how excellent this company is. I inherited a house with a 2007 Hotspring Aria hot tub. The spa hasn’t been operated in years and when I turned it on, it ran for about 10 minutes and died. I mean dead died. I knew absolutely nothing about hot tubs but with the excellent diagnosis videos, installation videos and superior phone support, I was able to replace the main control board, heater relay board, heater, circulation pump, the ozonator and all associated tubing. This took 4 1/2 hours over two days (I had to watch videos) but the spa runs like new! I had one question regarding the jumper voltage 18 or 12. I spoke with a technician and he was able to answer my question as well as helping me double check the voltages for the components on the relay board. I am handy with electronics and electricity and am comfortable working with 230 volts. Shipping was fast and as expected. I highly recommend BackYardPlus.On 06/28/2024 by F. R. (verified customer)
Get Watkins Wavemaster Pumps, Circulation Pumps, Wet-end Kits, Impellers, Shaft Seals, O-rings, Compression Fittings, and other parts related to your pumps.
Showing 1–30 of 51 results
-
This is the complete circulation pump retrofit kit for Hot Spot SX tubs beginning in 2020 and Hot Spot TX tubs beginning in 2021 What's included: A Frog Bypass Assembly B Circulation Pump to Heater Inlet Assembly B1 2" Heater Inlet Conector with ...read more
-
This is the complete circulation pump retrofit kit for Hot Spot TX 2020 ONLY What's included: A Frog Bypass Assembly B Circulation Pump to Heater Inlet Assembly B1 2" Heater Inlet Conector with 3/4" barb fitting B2 1/4" Clear Vinyl Hose ...read more
-
This is the complete "wet end" of the jet pump Your Watkins Wavemaster 9000 & 9200 (v 2), 2 5 HP jet pump is comprised of two main components: the electric motor and the "wet end" In some cases, this entire "wet end kit" is needed Perfect remedy if ...read more
-
This is the complete "wet end" of the jet pump Your Wavemaster 9000 & 9200 (v 2), 2 5 HP jet pump is comprised of two main components: the electric motor and the "wet end" In some cases, this entire "wet end kit" is needed Perfect remedy if your "wet ...read more
-
This is the AFTER-MARKET "wet end" of the jet pump Your Wavemaster 9000 & 9200 (v 2), 2 5 HP jet pump is comprised of two main components: the electric motor and the "wet end" In some cases, this entire "wet end kit" is needed Perfect remedy if your ...read more
-
This is the complete"wet end" for the Wavemaster 8000 2 0 HP jet pump and Wavemaster 8200 2 0HP two-speed jet pump Your jet pump is comprised of two main components: the electric motor and the "wet end" In some cases, this entire "wet end kit" is needed ...read more
-
This is the entire "wet end" for the Wavemaster 8000 2 0 hp jet pump and Wavemaster 8200 2 0hp two-speed jet pump that can be found on Hot Spring and Limelight spas beginning in 2007
-
Sku: 72995-BYP
Wet End Kit, After Market, 2.0 hp Pump
This is the after-market wet end for the Wavemaster 8000 2 0 hp jet pump and Wavemaster 8200 2 0HP, 2-speed, 48 Frame jet pump -
This is the after-market wet end for the European Wavemaster 2 0 hp (3HP @ 60hz North American) 48 frame jet pump, model number 0965901
-
This is the AFTER-MARKET "wet end" for the 1 0HP pump The intake and discharge measure 2" This "wet end" will attach to your existing motor Your jet pump is comprised of two main components: the electric motor and the "wet end" In some cases, this entire ...read more
-
This is the AFTER-MARKET "wet end" of the jet pump Your Wavemaster 8000, 2 0 HP jet pump is comprised of two main components: the electric motor and the "wet end" In some cases, this entire "wet end kit" is needed Perfect remedy if your "wet end" has ...read more
-
This is the AFTER-MARKET "wet end" for the 1 0HP FMCP pump The intake and discharge measure 1-1/2" This "wet end" will attach to your existing motor Your jet pump is comprised of two main components: the electric motor and the "wet end" In some cases, ...read more
-
This is the AFTER-MARKET "wet end" for the 1 5HP FMHP pump The intake and discharge measure 1-1/2" This "wet end" will attach to your existing motor Your jet pump is comprised of two main components: the electric motor and the "wet end" In some cases, ...read more
-
Sku: 70331
Wet End Kit,0.75 hp, 48fr, Side Discharge, 1-1/2″ intake/discharge, Gecko Aquaflo FMHP series
This is the "wet end" for the 0 75 HP FMHP series pump (side discharge) The intake and discharge measure 1-1/2" This "wet end" will attach to your existing motor Your jet pump is comprised of two main components: the electric motor and the "wet end" In ...read more -
Sku: 33980-WETEND
Wet End, Wavemaster 5000 Replacement
This replaces the wet end on the obsolete Wavemaster® 5000 pump found on the pre-1997 Hot Spring and Tiger River spa models It is the complete wet end, FMHP series, 1 0HP (Orange Dot), 1-1/2" Intake / Side Discharge, 48 Frame -
Sku: 36070-WETEND
Wetend Kit, Watkins Wavemaster 7000 Jet Pump (v.1)
Wet end kit for the Watkins Wavemaster 7000 jet pump (v 1) 36070 pump The 36070 pump (36070-BYP) was used on the Hot Spring 1993-1996 Classic, 1993-1995 Grandee and Sovereign spa models This kit comes pre-assembled for shipping purposes It needs to be ...read more -
Sku: SK-WM-7000-V3-BYP
Complete Seal Kit, Wavemaster 7000 (ver.3)
Wet End Seal Kit for the Wavemaster 7000 (ver 3) Jet Pump These parts only fit the pumps with a vendor number ending in 4081 All the replacement parts necessary when opening up the "wet end" to cure a leaking pump Since the impeller typically breaks when ...read more -
The shaft seal kit is used to prevent water from leaking from around the rotating pump shaft This seal kit is used on most of the Watkins Wavemaster jet pumps and after-market jet pumps Please find your pump model number and if your pump is an OEM ...read more
-
The shaft seal kit is used to prevent water from leaking from around the rotating pump shaft This seal kit is used on most of the Watkins Wavemaster jet pumps and after-market jet pumps manufactured by LX (Lingxiao) Please find your pump model number and ...read more
-
Sku: 36675-01SS
Shaft Seal, Watkins Wavemaster 7000 Jet Pump, Vico Ultimax
The shaft seal kit is used to prevent water from leaking from around the rotating pump shaft This shaft seal will only work with the Vico brand wet end An indicator that your Watkins Wavemaster jet pump was made by Vico is the model number will end in "-01" ...read more -
Sku: 30240
Volute O-ring, Wavemaster
Large o-ring that fits in between the two halves of the "wet end" (volute & volute cover) of the FMHP Series Wavemaster 3000, Wavemaster 5000 & Wavemaster 8000 jet pumps -
Sku: 30217
Volute, Starite
This Sta-rite volute is the front part of the "wet end" of the 1HP and 2HP Max-E-Glas jet pumps used on the Hot Spring spa models prior to 1993 -
Sku: 70032-BYP
Seal Plate Kit, Starite- After Market
This after-market (Sta-rite) seal plate is the part of the "wet end" that bolts onto the pump motor This seal plate is the replacement for both the 1hp and 2hp Starite Max-E-Glas jet pumps used on Hot Spring models prior to 1993 Please note, the pump ...read more -
Sku: 70400-BYP
Shaft Seal, Wavemaster 7000 (v.1)
This shaft seal is for the Wavemaster 7000 (v 1) Sta-rite 5/8" shaft seal used on the 1HP and 2HP jet pumps that were built from 1998 forward This seal is used with the seal plate that DOES NOT require the copper heater sink If you are repairing a pump ...read more -
Sku: 30224
Starite Shaft Seal
Sta-rite shaft seal used on the 1HP and 2HP jet pumps that use a copper heat sink on Hot Spring spas Reference number: U109-93SS -
This heavy-duty fiberglass-reinforced polymer split nut comes in two pieces and is designed to replace compression fitting nuts (aka pump union nuts) that have broken due to vibration, age and finally over-tightening The two halves of this fitting are held ...read more
-
This is the after-market 3/4" Replacement Shaft Seal for the Wavemaster 7000 version 2 and the Wavemaster 9000
-
Sku: 71030
Shaft Seal, Wavemaster 7000 (version 2) and 9000
This item is obsolete and replaced by:
71030-BYPReplacement Shaft Seal for the Wavemaster 7000 version 2 and the Wavemaster 9000 See item 71030-BYP for after-market shaft seal -
Sku: 34470
Jet Pump Ring Adapter 1-1/2in X 2in
This adapter converts the jet pump 1-1/2" inlet and outlet (suction & discharge) to 2" It has threads on the inside and outside and is used on various Hot Spring, Tiger River, and Hot Spot spa models This item is most often used on the Wavemaster 3000 ...read more -
Used to convert 1/2" plumbing to 3/4" on pre-1990 Hot Springs only This kit contains all the fittings & tubing necessary to convert your 1/2" plumbing to 3/4" when replacing the older style 1/2" inlet/outlet Hot Spring circulating pumps to the new ...read more
Showing 1–30 of 51 results